Polycom 6400-S manual Enabling Snmp

Page 59

Administrative Options

Caution When manually configuring the MTU size we recommend that you use a setting of 800 bytes or greater. You may experience problems with certain types of VoIP traffic if the MTU size is set below 800 bytes.

To set the Provider MTU size:

1.In the navigation bar, select System.

2.In the System menu, select Set Link.

3.Enter the Provider MTU size.

4.Press Submit.

Enabling SNMP

The 6400-S can be managed remotely by an SNMP network management system such as HP Openview. The 6400-S supports SNMPv1 and MIB-II (RFC1213). All MIB-II variables are read only. The MIB variables sysContact and sysLocation are set by the web GUI.

To enable SNMP:

1.In the Navigation bar, select System.

7 - 13

Image 59

Contents User Guide V2IU 6400-S Converged Network Appliance Trademark Information Contents Administrative Options Configuring Network SettingsConfiguring VoIP Configuring the FirewallContents User Guide V2IU 6400-S Converged Network Appliance Introducing the V2IU 6400-S Converged Network Appliance IntroductionService Provider E-1NxT-1/E-1 Branch Office Physical Connections and Specifications FeaturesManagement Features User Guide V2IU 6400-S Converged Network Appliance If AC power supplies are installed Installing the 6400-SPhysical Installation1 If DC power supplies are installed DC Power Supply Interface Requirements Power Supplies1DC Power Supply LED Indicators AC Power Supply Interface RequirementsConnecting to the 6400-S Configuring the V2IU 6400-SUser Guide V2IU 6400-S Converged Network Appliance Logging in and out of the 6400-S Navigating through the configuration pagesGetting information about the network Getting helpRouting Information Getting information about the system System uptime Recent Call Log Configuring subscriber interface settings Configuring Network SettingsConfiguring provider interface settings Setting the Ethernet link rate Link speed and duplex with locally attached devices Setting Description Configuring the NetworkTo configure network settings Configuring VoIP To configure VoIP ALG Configuring VoIP Field Description Currently registered Configuring VoIP subnet routing Deleting a VoIP subnet route Configuring sofswitch survivability Configuring VoIP survivabilitySoftswitch redundancy configuration To configure Sofswitch Redundancy, enter the following Configuring VrrpConfiguring VoIP User Guide V2IU 6400-S Converged Network Appliance Configuring the firewall basic settings Configuring the FirewallTo configure basic settings Basic settings rules Configuring advanced firewall settingsEnabling or disabling the firewall Advanced setting rulesChanging the administration password Administrative OptionsSpecifying user commands Managing SIP, Mgcp or H.323 clients Deleting clients Selecting a clientAdding clients Querying clientsRestarting the network Rebooting the systemUsing Network Test Tools Running a traceroute test Running a ping testUpgrading the firmware Configuring the interface Configuring a management interfaceReconnecting the 6400-S Move the connection from Port 2 to Port Configuring the trusted management addressesSetting the Provider MTU size Enabling Snmp Field Description Enabling remote system logging Disabling SnmpAddressport Disabling remote system logging Setting the system date and timeCreating a static route Deleting a static route User Guide V2IU 6400-S Converged Network Appliance No dial tone Troubleshooting TipsTrouble accessing the Internet AppendixChecking the ALG registration code Telephone doesnt register with the softswitchChecking the configurations on the ALG Pinging the softswitchRegulatory Notices Important SafeguardsOther Rights and Limitations Regulatory Notices Warranty and Warranty Exclusions Regulatory Notices Miscellaneous Regulatory Notices User Guide V2IU 6400-S Converged Network Appliance Regulatory Notices User Guide V2IU 6400-S Converged Network Appliance Regulatory Notices Compliance and Compatibility1 Regulatory Notices