Polycom Installing the 6400-S, Physical Installation1, If AC power supplies are installed

Page 13

2

Installing the 6400-S

Physical Installation1

Anchor the equipment rack that will contain the 6400.

The equipment rack must be anchored to an unmovable support to prevent it from falling over when one or more systems are extended in front of the rack on slides. You must also consider the weight of any other device installed in the rack. A crush hazard exists should the rack tilt forward which could cause serious injury.

If AC power supplies are installed

Mains AC power disconnect

The AC power cord(s) is considered the mains disconnect for the 6400-S and must be readily accessible when installed. If the individual server power cord(s) will not be readily accessible for disconnection then you are responsible for installing an AC power disconnect for the entire rack unit. This main disconnect must be readily accessible, and it must be labeled as controlling power to the entire rack, not just to the 6400-S(s). To remove all power, two AC cords must be removed.

Grounding the rack installation

To avoid the potential for an electrical shock hazard, you must include a third wire safety ground conductor with the rack installation. If the 6400-S power cord is plugged into an AC outlet that is part of the rack, then you must provide proper grounding for the rack itself. If the 6400-S power cord is plugged into a wall AC outlet, the safety ground conductor in the power cord provides proper grounding only for the 6400-S. You must provide additional, proper grounding for the rack and other devices installed in it.

1 Intel® Telco/Industrial Grade Server TIGPR2U Product Guide

2 - 1

Image 13

Contents User Guide V2IU 6400-S Converged Network Appliance Trademark Information Contents Configuring VoIP Configuring Network SettingsConfiguring the Firewall Administrative OptionsContents User Guide V2IU 6400-S Converged Network Appliance Introducing the V2IU 6400-S Converged Network Appliance IntroductionService Provider E-1NxT-1/E-1 Branch Office Physical Connections and Specifications FeaturesManagement Features User Guide V2IU 6400-S Converged Network Appliance Physical Installation1 Installing the 6400-SIf AC power supplies are installed If DC power supplies are installed DC Power Supply Interface Requirements Power Supplies1DC Power Supply LED Indicators AC Power Supply Interface RequirementsConnecting to the 6400-S Configuring the V2IU 6400-SUser Guide V2IU 6400-S Converged Network Appliance Logging in and out of the 6400-S Navigating through the configuration pagesGetting information about the network Getting helpRouting Information Getting information about the system System uptime Recent Call Log Configuring subscriber interface settings Configuring Network SettingsConfiguring provider interface settings Setting the Ethernet link rate Link speed and duplex with locally attached devices Setting Description Configuring the NetworkTo configure network settings Configuring VoIP To configure VoIP ALG Configuring VoIP Field Description Currently registered Configuring VoIP subnet routing Deleting a VoIP subnet route Configuring sofswitch survivability Configuring VoIP survivabilitySoftswitch redundancy configuration To configure Sofswitch Redundancy, enter the following Configuring VrrpConfiguring VoIP User Guide V2IU 6400-S Converged Network Appliance Configuring the firewall basic settings Configuring the FirewallTo configure basic settings Basic settings rules Configuring advanced firewall settingsEnabling or disabling the firewall Advanced setting rulesChanging the administration password Administrative OptionsSpecifying user commands Managing SIP, Mgcp or H.323 clients Deleting clients Selecting a clientAdding clients Querying clientsUsing Network Test Tools Rebooting the systemRestarting the network Running a traceroute test Running a ping testUpgrading the firmware Configuring the interface Configuring a management interfaceReconnecting the 6400-S Move the connection from Port 2 to Port Configuring the trusted management addressesSetting the Provider MTU size Enabling Snmp Field Description Enabling remote system logging Disabling SnmpAddressport Disabling remote system logging Setting the system date and timeCreating a static route Deleting a static route User Guide V2IU 6400-S Converged Network Appliance Trouble accessing the Internet Troubleshooting TipsAppendix No dial toneChecking the configurations on the ALG Telephone doesnt register with the softswitchPinging the softswitch Checking the ALG registration codeRegulatory Notices Important SafeguardsOther Rights and Limitations Regulatory Notices Warranty and Warranty Exclusions Regulatory Notices Miscellaneous Regulatory Notices User Guide V2IU 6400-S Converged Network Appliance Regulatory Notices User Guide V2IU 6400-S Converged Network Appliance Regulatory Notices Compliance and Compatibility1 Regulatory Notices