Polycom 6400-S manual Specifying user commands

Page 48

User Guide V2IU 6400-S Converged Network Appliance

2.On the System page, locate Change Password, and follow this link: The password of the device can be changed.

3.Enter the New Password. The new password must be between 6 and 20 characters in length. Any combination of alpha and numeric characters is accepted.

4.Enter the password again in the Confirm Password to ensure that there were no mistakes in the initial entry.

5.Press Submit.

Specifying user commands

User commands allow you to execute special operations that may be required for your installation, such as creating user specific firewall or routing rules.

Examples:

ifconfig eth0:20 192.168.20.10 netmask 255.255.255.0

iptables -I POSTROUTING -t nat -s 192.168.20.10 -j ACCEPT

Caution Use caution when adding user commands. The system may become unreachable if an incorrect command is entered.

7 - 2

Image 48

Contents User Guide V2IU 6400-S Converged Network Appliance Trademark Information Contents Configuring Network Settings Configuring VoIPConfiguring the Firewall Administrative OptionsContents User Guide V2IU 6400-S Converged Network Appliance Introduction Introducing the V2IU 6400-S Converged Network ApplianceService Provider E-1NxT-1/E-1 Branch Office Features Physical Connections and SpecificationsManagement Features User Guide V2IU 6400-S Converged Network Appliance Installing the 6400-S Physical Installation1If AC power supplies are installed If DC power supplies are installed Power Supplies1 DC Power Supply Interface RequirementsAC Power Supply Interface Requirements DC Power Supply LED IndicatorsConfiguring the V2IU 6400-S Connecting to the 6400-SUser Guide V2IU 6400-S Converged Network Appliance Navigating through the configuration pages Logging in and out of the 6400-SGetting help Getting information about the networkRouting Information Getting information about the system System uptime Recent Call Log Configuring Network Settings Configuring subscriber interface settingsConfiguring provider interface settings Setting the Ethernet link rate Link speed and duplex with locally attached devices Configuring the Network Setting DescriptionTo configure network settings Configuring VoIP To configure VoIP ALG Configuring VoIP Field Description Currently registered Configuring VoIP subnet routing Deleting a VoIP subnet route Configuring VoIP survivability Configuring sofswitch survivabilitySoftswitch redundancy configuration Configuring Vrrp To configure Sofswitch Redundancy, enter the followingConfiguring VoIP User Guide V2IU 6400-S Converged Network Appliance Configuring the Firewall Configuring the firewall basic settingsTo configure basic settings Configuring advanced firewall settings Basic settings rulesAdvanced setting rules Enabling or disabling the firewallAdministrative Options Changing the administration passwordSpecifying user commands Managing SIP, Mgcp or H.323 clients Selecting a client Deleting clientsQuerying clients Adding clientsRebooting the system Using Network Test ToolsRestarting the network Running a ping test Running a traceroute testUpgrading the firmware Configuring a management interface Configuring the interfaceReconnecting the 6400-S Configuring the trusted management addresses Move the connection from Port 2 to PortSetting the Provider MTU size Enabling Snmp Field Description Disabling Snmp Enabling remote system loggingAddressport Setting the system date and time Disabling remote system loggingCreating a static route Deleting a static route User Guide V2IU 6400-S Converged Network Appliance Troubleshooting Tips Trouble accessing the InternetAppendix No dial toneTelephone doesnt register with the softswitch Checking the configurations on the ALGPinging the softswitch Checking the ALG registration codeImportant Safeguards Regulatory NoticesOther Rights and Limitations Regulatory Notices Warranty and Warranty Exclusions Regulatory Notices Miscellaneous Regulatory Notices User Guide V2IU 6400-S Converged Network Appliance Regulatory Notices User Guide V2IU 6400-S Converged Network Appliance Regulatory Notices Compliance and Compatibility1 Regulatory Notices