BenQ MS521 user manual Presentation, Timer, Language, Projector, Installation, Menu, Settings

Page 54

FUNCTION

 

 

 

Presentation

 

4.

 

Timer

 

 

 

Basicmenu

SYSTEMSETUP:

 

Language

 

Projector

 

 

 

 

 

 

Installation

 

 

 

Menu

 

 

 

Settings

 

 

 

 

DESCRIPTION

Reminds the presenter to finish the presentation within a certain time frame. See "Setting the presentation timer" on page 39 for details.

Sets the language for the On-Screen Display (OSD) menus. See "Using the menus" on page 28 for details.

The projector can be installed on a ceiling or behind a screen, or with one or more mirrors. See "Choosing a location" on page 15 for details.

Menu display Time

Sets the length of time the OSD will remain active after your last key press. The range is from 5 to 30 seconds in 5-second increments.

Menu Position

Sets the On-Screen Display (OSD) menu position.

Reminder message

Sets whether to display the reminder message.

54 Operation

Page 53 Page 55
Image 54
Page 53 Page 55
Contents User Man ual Table of contents Uninterruptible power supply Areas where the mains voltageYour projector through a power Refer servicing to qualified service personnelSafety Instructions Do not block the ventilation holes Safety Instructions Projector features Shipping contents Projector exterior view Rear/lower sideControls and functions Ceiling mounting the projector Remote control Source Volume +Setting MuteReplacing the remote control battery Choosing a location Front TableFront Ceiling Projection dimensions Obtaining a preferred projected image sizeMS521/MX522/MS511H MW523/TW523 762 646 404Connection Connecting a monitor Connecting a computer or monitorConnecting a computer To connect the projector to a notebook or desktop computerConnecting Video source devices Connecting a Hdmi source device To connect the projector to a Hdmi source deviceConnecting a Component Video source device To connect the projector to a Component Video source deviceConnecting an S-Video/composite source device To connect the projector to an S-Video/Video source deviceOperation Starting up the projectorAdjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image size and clarity Use build-in test patternCorrecting keystone Using the menus Setting a password Using a security cable lockUtilizing the password function Securing the projectorIf you forget the password Entering the password recall procedureChanging the password Disabling the password function Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioAbout the aspect ratio Go to the Picture Picture Mode menu Selecting a picture modeSetting the User 1/User 2 mode Optimizing the imageUsing Wall Color Fine-tuning the image quality in user modes3D Color Management Setting a preferred color temperatureAbout color temperatures Press MODE/ENTER and the 3D Color Management page displaysMagenta Cyan Setting the presentation timer Selection DescriptionTop-Left Bottom-Left Top-Right Bottom-Right To cancel the timer, perform the following steps How to use the Timer On key?Remote paging operations Hiding the image Freezing the imageTo activate the High Altitude Mode Adjusting the soundAdjusting the sound level Operating in a high altitude environmentUse Teaching Template Lamp Mode Description Select the lamp saver modeUntil the System Setup Advanced menu is highlighted Personalizing the projector menu displayShutting down the projector Menu operation Menu systemMain menu Sub-menu Options Picture System Setup Basic Setup AdvancedDescription of each menu Teaching TemplateReference Picture ModePicture menu ModeReset Picture Temperature ColorTemperature Fine Tuning 3D Color SettingSettings TimerInstallation PresentationPanel Key Basic menuOperation LockAudio System Setup Advanced menuHigh Altitude LampCaption Reset AllClosed StandbySystem Information menuCurrent StatusCare of the projector Cleaning the lensCleaning the projector case Storing the projectorLamp information Setting Lamp mode eco function as Economic or SmartEco modeSetting Auto Power Off Getting to know the lamp hourPage Timing of replacing the lamp Status MessageReplacing the lamp Page Resetting the lamp timer Indicators Green Green Flashing Flashing Off Projector does not turn on Remote control does not workPassword is incorrect No pictureSpecifications Dimensions Ceiling mount installation301.6 219.2 111.3 Timing chart Resolution Mode Vertical Horizontal Pixel Frequency KHz MHzSupported timing for PC input Supported timing for Hdmi Hdcp input HDMI/DVI Supported timing for Component-YPbPr input Supported timing for Video and S-Video inputSupported 3D signal for Hdmi Hdcp input Video timingPC timing Supported 3D signal for D-SUB input SXGA85Supported 3D signal for Video and S-Video input Copyright Limited warrantyPatents DisclaimerFCC statement for the United States only Warranty and Copyright information For UK only CE DOC KONFORMITÄTSERKLÄRUNG Konformitetsdeklaration Uyum Beyani Deklaracija O Usklaĉenosti Overensstemmelseserklæring Vaatimustenmukaisuusvakuutus Weee directive Directiva Weee Ⱦɢɪɟɤɬɢɜɚ Weee Dyrektywa Weee Directiva REE Weee direktiva ȄįȘȖȓĮ Weee For Korea WLAN/BT module Warranty and Copyright information Weee UAE Singapore
Top Page Image Contents