BenQ MS521 user manual FCC statement for the United States only

Page 79

FCC statement (for the United States only)

CLASS B: This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the distance between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Operation is subject to the following two conditions:

1)this device may not cause interference and

2)this device must accept any interference, including interference that may cause undesired operation of the device.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

Warranty and Copyright information 79

Image 79
Contents User Man ual Table of contents Refer servicing to qualified service personnel Areas where the mains voltageYour projector through a power Uninterruptible power supplySafety Instructions Do not block the ventilation holes Safety Instructions Projector features Shipping contents Rear/lower side Projector exterior viewControls and functions Ceiling mounting the projector Remote control Mute Volume +Setting SourceReplacing the remote control battery Front Table Choosing a locationFront Ceiling Obtaining a preferred projected image size Projection dimensionsMS521/MX522/MS511H 762 646 404 MW523/TW523Connection To connect the projector to a notebook or desktop computer Connecting a computer or monitorConnecting a computer Connecting a monitorConnecting Video source devices To connect the projector to a Hdmi source device Connecting a Hdmi source deviceTo connect the projector to a Component Video source device Connecting a Component Video source deviceTo connect the projector to an S-Video/Video source device Connecting an S-Video/composite source deviceStarting up the projector OperationAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Use build-in test pattern Fine-tuning the image size and clarityCorrecting keystone Using the menus Securing the projector Using a security cable lockUtilizing the password function Setting a passwordEntering the password recall procedure If you forget the passwordChanging the password Disabling the password function Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Optimizing the image Selecting a picture modeSetting the User 1/User 2 mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes Using Wall ColorPress MODE/ENTER and the 3D Color Management page displays Setting a preferred color temperatureAbout color temperatures 3D Color ManagementMagenta Cyan Selection Description Setting the presentation timerTop-Left Bottom-Left Top-Right Bottom-Right How to use the Timer On key? To cancel the timer, perform the following stepsRemote paging operations Freezing the image Hiding the imageOperating in a high altitude environment Adjusting the soundAdjusting the sound level To activate the High Altitude ModeUse Teaching Template Personalizing the projector menu display Select the lamp saver modeUntil the System Setup Advanced menu is highlighted Lamp Mode DescriptionShutting down the projector Menu system Menu operationMain menu Sub-menu Options Picture System Setup Basic Advanced SetupDescription of each menu Template TeachingMode Picture ModePicture menu ReferenceSetting Temperature ColorTemperature Fine Tuning 3D Color Reset PicturePresentation TimerInstallation SettingsLock Basic menuOperation Panel KeyLamp System Setup Advanced menuHigh Altitude AudioStandby Reset AllClosed CaptionStatus Information menuCurrent SystemStoring the projector Cleaning the lensCleaning the projector case Care of the projectorGetting to know the lamp hour Setting Lamp mode eco function as Economic or SmartEco modeSetting Auto Power Off Lamp informationPage Status Message Timing of replacing the lampReplacing the lamp Page Resetting the lamp timer Indicators Green Green Flashing Flashing Off No picture Remote control does not workPassword is incorrect Projector does not turn onSpecifications Ceiling mount installation Dimensions301.6 219.2 111.3 Resolution Mode Vertical Horizontal Pixel Frequency KHz MHz Timing chartSupported timing for PC input Supported timing for Hdmi Hdcp input HDMI/DVI Supported timing for Video and S-Video input Supported timing for Component-YPbPr inputVideo timing Supported 3D signal for Hdmi Hdcp inputPC timing SXGA85 Supported 3D signal for D-SUB inputSupported 3D signal for Video and S-Video input Disclaimer Limited warrantyPatents CopyrightFCC statement for the United States only Warranty and Copyright information For UK only CE DOC KONFORMITÄTSERKLÄRUNG Konformitetsdeklaration Uyum Beyani Deklaracija O Usklaĉenosti Overensstemmelseserklæring Vaatimustenmukaisuusvakuutus Weee directive Directiva Weee Ⱦɢɪɟɤɬɢɜɚ Weee Dyrektywa Weee Directiva REE Weee direktiva ȄįȘȖȓĮ Weee For Korea WLAN/BT module Warranty and Copyright information Weee UAE Singapore