BenQ MS521 user manual Resetting the lamp timer

Page 65

7.Tighten the screws that secure the

lamp.

• Loose screw may cause a bad connection, which could result in malfunction.

•Do not over tighten the screws.

8.Ensure the handle is fully laid flat and

locked in place.

9.Replace the lamp cover by sliding it into place.

(a)

(b)

10.Tighten the screw that secures the lamp cover.

•Loose screw may cause a bad connection, which could result in malfunction.

•Do not over tighten the screw.

11.Restart the projector.

Do not turn the power on with the lamp cover removed.

Resetting the lamp timer

12.After the startup logo, open the On-Screen Display (OSD) menu. Go to the SYSTEM SETUP: Advanced > Lamp Settings menu. Press Mode/Enter. The Lamp

Settings page displays. Press to highlight Reset lamp timer and press Mode/Enter.

A warning message displays asking if you want to reset the lamp timer. Highlight Reset and press Mode/Enter. The lamp time will be reset to '0'.

Do not reset if the lamp is not new or replaced as this could cause damage.

Maintenance 65

Image 65

Contents User Man ual Table of contents Your projector through a power Areas where the mains voltageUninterruptible power supply Refer servicing to qualified service personnelSafety Instructions Do not block the ventilation holes Safety Instructions Projector features Shipping contents Rear/lower side Projector exterior viewControls and functions Ceiling mounting the projector Remote control Setting Volume +Source MuteReplacing the remote control battery Front Ceiling Choosing a locationFront Table MS521/MX522/MS511H Projection dimensionsObtaining a preferred projected image size 762 646 404 MW523/TW523Connection Connecting a computer Connecting a computer or monitorConnecting a monitor To connect the projector to a notebook or desktop computerConnecting Video source devices To connect the projector to a Hdmi source device Connecting a Hdmi source deviceTo connect the projector to a Component Video source device Connecting a Component Video source deviceTo connect the projector to an S-Video/Video source device Connecting an S-Video/composite source deviceStarting up the projector OperationAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle Use build-in test pattern Fine-tuning the image size and clarityCorrecting keystone Using the menus Utilizing the password function Using a security cable lockSetting a password Securing the projectorChanging the password If you forget the passwordEntering the password recall procedure Disabling the password function Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Setting the User 1/User 2 mode Selecting a picture modeGo to the Picture Picture Mode menu Optimizing the imageFine-tuning the image quality in user modes Using Wall ColorAbout color temperatures Setting a preferred color temperature3D Color Management Press MODE/ENTER and the 3D Color Management page displaysMagenta Cyan Top-Left Bottom-Left Top-Right Bottom-Right Setting the presentation timerSelection Description Remote paging operations To cancel the timer, perform the following stepsHow to use the Timer On key? Freezing the image Hiding the imageAdjusting the sound level Adjusting the soundTo activate the High Altitude Mode Operating in a high altitude environmentUse Teaching Template Until the System Setup Advanced menu is highlighted Select the lamp saver modeLamp Mode Description Personalizing the projector menu displayShutting down the projector Main menu Sub-menu Options Menu operationMenu system Picture System Setup Basic Advanced SetupDescription of each menu Template TeachingPicture menu Picture ModeReference ModeTemperature Fine Tuning 3D Color Temperature ColorReset Picture SettingInstallation TimerSettings PresentationOperation Basic menuPanel Key LockHigh Altitude System Setup Advanced menuAudio LampClosed Reset AllCaption StandbyCurrent Information menuSystem StatusCleaning the projector case Cleaning the lensCare of the projector Storing the projectorSetting Auto Power Off Setting Lamp mode eco function as Economic or SmartEco modeLamp information Getting to know the lamp hourPage Status Message Timing of replacing the lampReplacing the lamp Page Resetting the lamp timer Indicators Green Green Flashing Flashing Off Password is incorrect Remote control does not workProjector does not turn on No pictureSpecifications 301.6 219.2 111.3 DimensionsCeiling mount installation Supported timing for PC input Timing chartResolution Mode Vertical Horizontal Pixel Frequency KHz MHz Supported timing for Hdmi Hdcp input HDMI/DVI Supported timing for Video and S-Video input Supported timing for Component-YPbPr inputPC timing Supported 3D signal for Hdmi Hdcp inputVideo timing SXGA85 Supported 3D signal for D-SUB inputSupported 3D signal for Video and S-Video input Patents Limited warrantyCopyright DisclaimerFCC statement for the United States only Warranty and Copyright information For UK only CE DOC KONFORMITÄTSERKLÄRUNG Konformitetsdeklaration Uyum Beyani Deklaracija O Usklaĉenosti Overensstemmelseserklæring Vaatimustenmukaisuusvakuutus Weee directive Directiva Weee Ⱦɢɪɟɤɬɢɜɚ Weee Dyrektywa Weee Directiva REE Weee direktiva ȄįȘȖȓĮ Weee For Korea WLAN/BT module Warranty and Copyright information Weee UAE Singapore