BenQ MS521 user manual Timing of replacing the lamp, Status Message

Page 62

Timing of replacing the lamp

When the Lamp indicator lights up red or a message appears suggesting it is time to replace the lamp, please install a new lamp or consult your dealer. An old lamp may cause a malfunction in the projector and in some instances the lamp may explode.

Do not attempt to replace the lamp yourself. Contact the qualified service personnel for replacement.

The Lamp indicator light and Temperature warning light will light up if the lamp becomes too hot. See "Indicators" on page 66 for details.

The following lamp warning displays will remind you to change the lamp.

The warning messages below are for reference only. Please follow the actual on-screen instructions to prepare and replace the lamp.

Status	Message
Install a new lamp for optimal performance. If the
projector is normally run with Economic
selected ("Setting Lamp mode eco function as
Economic or SmartEco mode" on page 60), you
may continue to operate the projector until the
next lamp warning appears.

A new lamp should be fitted to avoid the
inconvenience when the projector runs out of
lamp time.

It is strongly recommended that you replace the
lamp at this stage. The lamp is a consumable item.
The lamp brightness diminishes with use. This is
normal lamp behavior. You can replace the lamp
whenever you notice that the brightness level has
significantly diminished.

The lamp MUST be replaced before the projector
will operate normally.

"XXXX" shown in the above messages are numbers that vary depending on different models.

62 Maintenance

Image 62

Contents User Man ual Table of contents Uninterruptible power supply Areas where the mains voltageYour projector through a power Refer servicing to qualified service personnelSafety Instructions Do not block the ventilation holes Safety Instructions Projector features Shipping contents Projector exterior view Rear/lower sideControls and functions Ceiling mounting the projector Remote control Source Volume +Setting MuteReplacing the remote control battery Front Ceiling Choosing a locationFront Table MS521/MX522/MS511H Projection dimensionsObtaining a preferred projected image size MW523/TW523 762 646 404Connection Connecting a monitor Connecting a computer or monitorConnecting a computer To connect the projector to a notebook or desktop computerConnecting Video source devices Connecting a Hdmi source device To connect the projector to a Hdmi source deviceConnecting a Component Video source device To connect the projector to a Component Video source deviceConnecting an S-Video/composite source device To connect the projector to an S-Video/Video source deviceOperation Starting up the projectorAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarity Use build-in test patternCorrecting keystone Using the menus Setting a password Using a security cable lockUtilizing the password function Securing the projectorChanging the password If you forget the passwordEntering the password recall procedure Disabling the password function Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioAbout the aspect ratio Go to the Picture Picture Mode menu Selecting a picture modeSetting the User 1/User 2 mode Optimizing the imageUsing Wall Color Fine-tuning the image quality in user modes3D Color Management Setting a preferred color temperatureAbout color temperatures Press MODE/ENTER and the 3D Color Management page displaysMagenta Cyan Top-Left Bottom-Left Top-Right Bottom-Right Setting the presentation timerSelection Description Remote paging operations To cancel the timer, perform the following stepsHow to use the Timer On key? Hiding the image Freezing the imageTo activate the High Altitude Mode Adjusting the soundAdjusting the sound level Operating in a high altitude environmentUse Teaching Template Lamp Mode Description Select the lamp saver modeUntil the System Setup Advanced menu is highlighted Personalizing the projector menu displayShutting down the projector Main menu Sub-menu Options Menu operationMenu system Picture System Setup Basic Setup AdvancedDescription of each menu Teaching TemplateReference Picture ModePicture menu ModeReset Picture Temperature ColorTemperature Fine Tuning 3D Color SettingSettings TimerInstallation PresentationPanel Key Basic menuOperation LockAudio System Setup Advanced menuHigh Altitude LampCaption Reset AllClosed StandbySystem Information menuCurrent StatusCare of the projector Cleaning the lensCleaning the projector case Storing the projectorLamp information Setting Lamp mode eco function as Economic or SmartEco modeSetting Auto Power Off Getting to know the lamp hourPage Timing of replacing the lamp Status MessageReplacing the lamp Page Resetting the lamp timer Indicators Green Green Flashing Flashing Off Projector does not turn on Remote control does not workPassword is incorrect No pictureSpecifications 301.6 219.2 111.3 DimensionsCeiling mount installation Supported timing for PC input Timing chartResolution Mode Vertical Horizontal Pixel Frequency KHz MHz Supported timing for Hdmi Hdcp input HDMI/DVI Supported timing for Component-YPbPr input Supported timing for Video and S-Video inputPC timing Supported 3D signal for Hdmi Hdcp inputVideo timing Supported 3D signal for D-SUB input SXGA85Supported 3D signal for Video and S-Video input Copyright Limited warrantyPatents DisclaimerFCC statement for the United States only Warranty and Copyright information For UK only CE DOC KONFORMITÄTSERKLÄRUNG Konformitetsdeklaration Uyum Beyani Deklaracija O Usklaĉenosti Overensstemmelseserklæring Vaatimustenmukaisuusvakuutus Weee directive Directiva Weee Ⱦɢɪɟɤɬɢɜɚ Weee Dyrektywa Weee Directiva REE Weee direktiva ȄįȘȖȓĮ Weee For Korea WLAN/BT module Warranty and Copyright information Weee UAE Singapore