Barco R9001560 manual Projector Mode Communication Port Green Operation

Page 15

Installation Set Up

Adjustment procedure adjustable lensholder.

Insert a wrench 13 mm into the slot on the front side of the projector.

 

 

PROJECTOR MODE:

 

 

COMMUNICATION PORT

GREEN - OPERATION

 

RS232 IN

(800-PERIPHERALS) REMOTE

RED - STANDBY

IR-RECEIVER

F10 AH / 250 V

FORCONTINUED PROTECTION AGAINST

RISKOF FIRE, REPLACE ONLYWITH

SAME TYPEAND RATING OF FUSE

R

G

B

H

V

R

G

B

H / C

V

To shift the image, grip the bolt with the wrench inside the cabinet and turn the wrench until the image is shifted to its correct place.

5976052 BARCOREALITY 9300 070999

 

4-3

 

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Reality 9300 DLC Federal communication commission FCC statement Date Art. No 070999 R5976052 Barco Projection SystemsTable of Contents Unpacking and Dimensions Projector dimensionsUnpacking Battery installation in the RCU Installation Guidelines Separate Sync Where to install the projector?How to install a projection lens? ComponentvideoControl Panel Terminology a. Local keypad Front Panel Terminology175 Remote controlRCU Location and Functions of Control FRONT/TABLE ConfigurationInstallation Configuration OSD Color@-40 Projector Mode Communication Port Green Operation Installation Set Up Fuses AC Power mains cord connectionSwitching on ConnectionsInput Connections Switching to Stand-bySwitching Off Lamp Run TimeRGB-SOG Peripheral Convergence Configuration Input SlotsFixed RGB analog input slot Input SlotsVideo Peripheral Convergence ConfigurationFixed 5-Input Slot slot Rgbhv Rgbs269,2VIDEO,1387 Video/S-video Input ModuleRGB Analog Input Module Component Input Module 2032117B-Y S9,2,1387Input Slots RGB3S / RG3sB Input Module 16HSDRUP UD \6HSDUDWH--6\QFV-VHOHFWLRQ\QFRQJUHHQ Serial Digital Input slotConnecting an IR Remote Receiver 800 to the projector Set up of the Baud Rate for Communication with a ComputerConnecting a Rcvds 05 to the projector Connecting a VS05 to the projectorControlling How to Use the RCU?Projector Address RCUPause key How to Display a Projector Address?How to Program an Address into the RCU? Picture Controls with Direct AccessPassword Start UP of the Adjustment ModeAdjustment Mode Random Access Installation ServiceRandom Access Adjustment Mode Starting up the Random Access Adjustment ModeFile Service Load File ServiceLoad File Edit FileHow to find the correct values for the displayed item? Read AmdsOptions Rename Field PolarityRename Delete CopyDelete CopyFile Sort Picture TuningColor Temperature File OptionsDecoding EBU GammaDecoding EBU/IRE GammaDynamic Color Depth Dynamic Color DepthNoise Reduction Input BalanceGeometry ShiftSize Blanking Side KeystoneBlanking Side KeystoneOptions Blanking TOP Bottom Left RightShift Size Side Keystone Blanking Input Slots Starting up the Installation ModeInfrared Communication How to AdjustTroubleshooting Peripheral Output module selectionEnter Green FocusingGreen to Midposition Blue on Green convergenceRed on Green convergence HatchAbout Moca No Signal BLACK/BLUE OSD color On-Screen DisplayInternal Patterns Service Mode Starting up the Service ModeService Identification Software versionIdentification Service Identification Change PasswordHow to enable or disable the password function ? How to change the password ?Change Baudrate PC Reset Lamp RuntimeChange Language Change Projector AddressLamp Drive Mode Lamp Run Time HistoryBarco logo I2C diagnosis Panel AdjustmentsPreset Input Balance UniformityStandard Source SET UP Files SUNXGA70 SUNEWS67SUNEWS76 SUNXGA60Lenses Focusing the lensLens Cleaning Procedure Cleaning procedure for HD1.5-31 lensLenses Projector without any 800 peripheral connected Projector with a 800 peripheral connectedSource numbers 90 Source numbers 81 13875&966285&6
Top Page Image Contents