Barco R9001560 manual Installation, Configuration OSD Color, Front/Table

Page 13

Installation Set Up

5HDU4&HLOLQJ

INSTALLATION SET )URQWUP&HLOLQJ

Configuration

The projector can be installed to project images in four different

5

configurationsHDU7DEOH

: front/table, front/ceiling, rear/table and rear/ceiling.

)UR

QW

7DEO

H

To change the Configuration, enter the adjustment mode by pushing ADJUST or ENTER. Highlight Installation by pushing the control disc forward or backward and press ENTER to select. The installation menu will be displayed.

ENTER displays the Installation menu.

EXIT or ADJUST returns to operational mode.

ADJUSTMENT MODE

Select a path from below :

RANDOM ACCESS

INSTALLATION

SERVICE

Source 01

Select with or

then <ENTER>

<EXIT> to return.

Highlight Configuration by pushing the control disc forward or backward and press ENTER to select. The configuration menu will be displayed.

ENTER displays the Configuration menu.

EXIT returns to the path selection menu.

ADJUST returns to operational mode.

INSTALLATION

INPUT SLOTS

800PERIPHERAL

CONVERGENCE

CONFIGURATION OSD COLOR

NO SIGNAL [BLACK] INTERNAL PATTERNS

Select with or then <ENTER> <EXIT> to return.

The actual selected configuration will be highlighted.

Push the control disc forward or backward to select the corresponding configuration with regard to the projector environment. Press ENTER to confirm your selection.

ENTER to confirm the selection.

EXIT returns to the installation menu.

ADJUST returns to operational mode.

CONFIGURATION

FRONT/TABLE

FRONT/CEILING

REAR/TABLE

REAR/CEILING

Select with or then <ENTER> <EXIT> to return.

5976052 BARCOREALITY 9300 070999		4-1

Image 13

Contents Reality 9300 DLC Federal communication commission FCC statement Date Art. No 070999 R5976052 Barco Projection SystemsTable of Contents Projector dimensions Unpacking and DimensionsUnpacking Battery installation in the RCU Installation Guidelines How to install a projection lens? Where to install the projector?Componentvideo Separate SyncControl Panel Terminology a. Local keypad Front Panel Terminology175 Remote controlRCU Location and Functions of Control Installation ConfigurationConfiguration OSD Color FRONT/TABLE@-40 Projector Mode Communication Port Green Operation Installation Set Up Switching on AC Power mains cord connectionConnections FusesSwitching Off Switching to Stand-byLamp Run Time Input ConnectionsFixed RGB analog input slot Peripheral Convergence Configuration Input SlotsInput Slots RGB-SOGFixed 5-Input Slot slot Peripheral Convergence ConfigurationRgbhv Rgbs Video269,2VIDEO,1387 Video/S-video Input ModuleRGB Analog Input Module 2032117B-Y S9,2,1387 Component Input ModuleInput Slots RGB3S / RG3sB Input Module 16HSDRUP UD \6HSDUDWH--6\QFV-VHOHFWLRQ\QFRQJUHHQ Serial Digital Input slotConnecting a Rcvds 05 to the projector Set up of the Baud Rate for Communication with a ComputerConnecting a VS05 to the projector Connecting an IR Remote Receiver 800 to the projectorControlling How to Use the RCU?Projector Address RCUHow to Program an Address into the RCU? How to Display a Projector Address?Picture Controls with Direct Access Pause keyAdjustment Mode Start UP of the Adjustment ModeRandom Access Installation Service PasswordStarting up the Random Access Adjustment Mode Random Access Adjustment ModeFile Service Load File File ServiceEdit File LoadRead Amds How to find the correct values for the displayed item?Options Field Polarity RenameRename Delete CopyCopy DeleteColor Temperature Picture TuningFile Options File SortDecoding EBU/IRE GammaGamma Decoding EBUNoise Reduction Dynamic Color DepthInput Balance Dynamic Color DepthShift GeometrySize Blanking Side KeystoneSide Keystone BlankingBlanking TOP Bottom Left Right OptionsShift Size Side Keystone Blanking Input Slots Starting up the Installation ModeTroubleshooting How to AdjustPeripheral Output module selection Infrared CommunicationGreen to Midposition Green FocusingBlue on Green convergence EnterHatch Red on Green convergenceAbout Moca OSD color On-Screen Display No Signal BLACK/BLUEInternal Patterns Starting up the Service Mode Service ModeService Software version IdentificationIdentification How to enable or disable the password function ? Change PasswordHow to change the password ? Service IdentificationChange Language Reset Lamp RuntimeChange Projector Address Change Baudrate PCLamp Run Time History Lamp Drive ModeBarco logo Preset Input Balance Panel AdjustmentsUniformity I2C diagnosisStandard Source SET UP Files SUNEWS76 SUNEWS67SUNXGA60 SUNXGA70Lens Cleaning Procedure Focusing the lensCleaning procedure for HD1.5-31 lens LensesLenses Projector with a 800 peripheral connected Projector without any 800 peripheral connectedSource numbers 90 Source numbers 81 13875&966285&6