Barco R9001560 manual Federal communication commission FCC statement

Page 2

Federal communication commission (FCC statement)

This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Instructions to the user :

if this equipment does cause interference to radio or television reception, the user may try to correct the interference by one or more of the following measures :

-Re-orientation of the receiving antenna for the radio or television.

-Relocate the equipment with respect to the receiver.

-Plug the equipment into a different outlet so that the equipment and receiver are on different branch circuits.

• Fasten cables connectors to the equipment by mounting screws.

Note :

The use of shielded cables is required to comply within the limits of Part15 of FCC rules and EN55022.

Due to constant research, the information in this manual is subject to change without notice.

Produced by BARCO NV, September 1999.

All rights reserved.

Trademarks are the rights of their respective owners.

BARCO n.v./Projection Systems

Noordlaan 5

B-8520 Kuurne

Belgium

Tel : +32/56/368211

Fax : +32/56/351651

E-mail : sales.bps@barco.com

Visite Barco at the web : http://www.barco.com

Printed in Belgium

Image 2
Contents Reality 9300 DLC Federal communication commission FCC statement Barco Projection Systems Date Art. No 070999 R5976052Table of Contents Unpacking Unpacking and DimensionsProjector dimensions Battery installation in the RCU Installation Guidelines Componentvideo Where to install the projector?How to install a projection lens? Separate SyncFront Panel Terminology Control Panel Terminology a. Local keypadRemote control 175RCU Location and Functions of Control Configuration OSD Color ConfigurationInstallation FRONT/TABLE@-40 Projector Mode Communication Port Green Operation Installation Set Up Connections AC Power mains cord connectionSwitching on FusesLamp Run Time Switching to Stand-bySwitching Off Input ConnectionsInput Slots Peripheral Convergence Configuration Input SlotsFixed RGB analog input slot RGB-SOGRgbhv Rgbs Peripheral Convergence ConfigurationFixed 5-Input Slot slot VideoVideo/S-video Input Module 269,2VIDEO,1387RGB Analog Input Module Input Slots Component Input Module2032117B-Y S9,2,1387 16HSDRUP UD \ RGB3S / RG3sB Input ModuleSerial Digital Input slot 6HSDUDWH--6\QFV-VHOHFWLRQ\QFRQJUHHQConnecting a VS05 to the projector Set up of the Baud Rate for Communication with a ComputerConnecting a Rcvds 05 to the projector Connecting an IR Remote Receiver 800 to the projectorHow to Use the RCU? ControllingRCU Projector AddressPicture Controls with Direct Access How to Display a Projector Address?How to Program an Address into the RCU? Pause keyRandom Access Installation Service Start UP of the Adjustment ModeAdjustment Mode PasswordFile Service Random Access Adjustment ModeStarting up the Random Access Adjustment Mode Edit File File ServiceLoad File LoadOptions How to find the correct values for the displayed item?Read Amds Rename RenameField Polarity Copy CopyDelete DeleteFile Options Picture TuningColor Temperature File SortGamma GammaDecoding EBU/IRE Decoding EBUInput Balance Dynamic Color DepthNoise Reduction Dynamic Color DepthSize GeometryShift Side Keystone Side KeystoneBlanking BlankingShift Size Side Keystone Blanking OptionsBlanking TOP Bottom Left Right Starting up the Installation Mode Input SlotsPeripheral Output module selection How to AdjustTroubleshooting Infrared CommunicationBlue on Green convergence Green FocusingGreen to Midposition EnterAbout Moca Red on Green convergenceHatch Internal Patterns No Signal BLACK/BLUEOSD color On-Screen Display Service Service ModeStarting up the Service Mode Identification IdentificationSoftware version How to change the password ? Change PasswordHow to enable or disable the password function ? Service IdentificationChange Projector Address Reset Lamp RuntimeChange Language Change Baudrate PCBarco logo Lamp Drive ModeLamp Run Time History Uniformity Panel AdjustmentsPreset Input Balance I2C diagnosisStandard Source SET UP Files SUNXGA60 SUNEWS67SUNEWS76 SUNXGA70Cleaning procedure for HD1.5-31 lens Focusing the lensLens Cleaning Procedure LensesLenses Source numbers 90 Projector without any 800 peripheral connectedProjector with a 800 peripheral connected Source numbers 81 13875&966285&6