Barco R9001560 manual Starting up the Installation Mode, Input Slots

Page 42

Installation Mode

9

INSTALLATION MODE

 

Starting up the Installation Mode

Push the cursor key or to highlight 'Installation Mode' and then press ENTER.

The following item can be selected in the Installation mode :

Input slots : to set up the input priority.

800 Peripheral : to select the type of output module used in the RCVDS05.

Convergence : to align the red, green and blue image.

Configuration : to set up the projector position.

OSD color : to change the color of the highlighted item.

No Signal : to display a black or blue screen when no source is connected to the projector.

Internal Patterns

Input Slots

The input configuration of the variable inputs is shown in the input slots menu. To view or to change the input configuration :

1Push the cursor key or to highlight 'Input Slots'.

2 Press ENTER to select.

The internal system will scan the input slots and displays the result in the Input slots menu.

Source

indication

Video or S-Video

Video[Video]

 

Video[S-Video]

RGB analog

RGB-SS[CV] : separate sync is composite video

 

signal on H/C input

 

RGB-SS[CS or HS&VS] : separate sync is

 

composite sync or horizontal and vertical

 

sync

 

RGB-SOG : sync on green

Component video

Component Video - SS : component video

 

with separate sync

 

Component Video - SOY : component video

 

with sync on Y

 

Component Video - 3LSS : component video

 

with 3 level separate sync.

 

Component Video - 3LSOY : component

 

video with 3 level sync on Y.

RGB analog with

 

tri-level sync

RGB3L-SS : RGB with separate Tri level sync

 

RGB3L-SOG : RGB with Tri level sync on

 

green

For slot 1 and slot 2, see chapter 'Connections'

If a RCVDS (switched on) or VS05 is connected to the projector, it will be also indicated on the menu by adding +800 peripheral. If no 800 peripheral indication is made on the menu, there are still two possi- bilities :

-no RCVDS or VS05 connected or

-RCVDS is switched off.

When a 800 peripheral is connected to the projector, the input slots are not accessible with the control disc to toggle their function.

ADJUSTMENT MODE

Select a path from below :

RANDOM ACCESS

INSTALLATION

SERVICE

Source 01

INSTALLATION

INPUT SLOTS

800 PERIPHERAL

CONVERGENCE

CONFIGURATION

OSD COLOR

NO SIGNAL [BLACK] INTERNAL PATTERNS

Select with or

then <ENTER>

<EXIT> to return.

INSTALLATION

INPUT SLOTS

800 PERIPHERAL

CONVERGENCE

CONFIGURATION

OSD COLOR

NO SIGNAL [BLACK] INTERNAL PATTERNS

Select with

or

 

then <ENTER>

 

<EXIT>

 

INPUT SLOTS

 

1. RGB-SS [CV]

 

2. RGB-SOG

 

3.

Video [Video]

 

4.

Component Video

 

5. Digital Input

9-1

 

5976052 BARCOREALITY 9300 070999

 

Image 42
Contents Reality 9300 DLC Federal communication commission FCC statement Barco Projection Systems Date Art. No 070999 R5976052Table of Contents Unpacking and Dimensions Projector dimensionsUnpacking Battery installation in the RCU Installation Guidelines Componentvideo Where to install the projector?How to install a projection lens? Separate SyncFront Panel Terminology Control Panel Terminology a. Local keypadRemote control 175RCU Location and Functions of Control Configuration OSD Color ConfigurationInstallation FRONT/TABLE@-40 Projector Mode Communication Port Green Operation Installation Set Up Connections AC Power mains cord connectionSwitching on FusesLamp Run Time Switching to Stand-bySwitching Off Input ConnectionsInput Slots Peripheral Convergence Configuration Input SlotsFixed RGB analog input slot RGB-SOGRgbhv Rgbs Peripheral Convergence ConfigurationFixed 5-Input Slot slot VideoVideo/S-video Input Module 269,2VIDEO,1387RGB Analog Input Module Component Input Module 2032117B-Y S9,2,1387Input Slots 16HSDRUP UD \ RGB3S / RG3sB Input ModuleSerial Digital Input slot 6HSDUDWH--6\QFV-VHOHFWLRQ\QFRQJUHHQConnecting a VS05 to the projector Set up of the Baud Rate for Communication with a ComputerConnecting a Rcvds 05 to the projector Connecting an IR Remote Receiver 800 to the projectorHow to Use the RCU? ControllingRCU Projector AddressPicture Controls with Direct Access How to Display a Projector Address?How to Program an Address into the RCU? Pause keyRandom Access Installation Service Start UP of the Adjustment ModeAdjustment Mode PasswordRandom Access Adjustment Mode Starting up the Random Access Adjustment ModeFile Service Edit File File ServiceLoad File LoadHow to find the correct values for the displayed item? Read AmdsOptions Rename Field PolarityRename Copy CopyDelete DeleteFile Options Picture TuningColor Temperature File SortGamma GammaDecoding EBU/IRE Decoding EBUInput Balance Dynamic Color DepthNoise Reduction Dynamic Color DepthGeometry ShiftSize Side Keystone Side KeystoneBlanking BlankingOptions Blanking TOP Bottom Left RightShift Size Side Keystone Blanking Starting up the Installation Mode Input SlotsPeripheral Output module selection How to AdjustTroubleshooting Infrared CommunicationBlue on Green convergence Green FocusingGreen to Midposition EnterRed on Green convergence HatchAbout Moca No Signal BLACK/BLUE OSD color On-Screen DisplayInternal Patterns Service Mode Starting up the Service ModeService Identification Software versionIdentification How to change the password ? Change PasswordHow to enable or disable the password function ? Service IdentificationChange Projector Address Reset Lamp RuntimeChange Language Change Baudrate PCLamp Drive Mode Lamp Run Time HistoryBarco logo Uniformity Panel AdjustmentsPreset Input Balance I2C diagnosisStandard Source SET UP Files SUNXGA60 SUNEWS67SUNEWS76 SUNXGA70Cleaning procedure for HD1.5-31 lens Focusing the lensLens Cleaning Procedure LensesLenses Projector without any 800 peripheral connected Projector with a 800 peripheral connectedSource numbers 90 Source numbers 81 13875&966285&6