Barco R9001560 Change Language, Change Projector Address, Change Baudrate PC, Reset Lamp Runtime

Page 50

Service Mode

Change Language

1Push the cursor key or to highlight 'Change Language'.

2 Press ENTER to display the language selection menu. Available languages : English

Change Projector Address

SERVICE

IDENTIFICATION

CHANGE PASSWORD

CHANGE LANGUAGE

CHANGE PROJ. ADDRESS

CHANGE BAUDRATE PC

RESET LAMP RUNTIME

LAMP RUNTINE HISTORY

Select with

CHANGE LANGUAGE

 

 

then

English

 

 

Select with

or

 

then <ENTER>

 

<EXIT> to

return.

Every projector requires an individual address between 0 and 255. This address can be software installed.

To change that address :

1Push the cursor key or to highlight 'Change Proj.

Address'.

2Press ENTER.

The Change Projector Address menu will be displayed and the actual address will be filled in.

The first digit is highlighted. Enter the new projector address with :

1the digit keys on the RCU or the local keypad or

2use the control disc to the right or to the left to select a digit and change the value by pushing the control disc up or down until the new value is reached. Continue with the other digits on the same way.

Change Baudrate PC

The communication speed between projector and computer, e.g. PC or MAC, has 8 possible speeds. The baud rate speed can be software set.

1Push the cursor key or to highlight 'Change Bau rate PC'.

2 Press ENTER to display the Change Baudrate PC menu.

The following baud rates are available :

230400/115200/57600/38400/19200/9600/4800/1200

The actual baud rate will be highlighted.

To change the baud rate :

1Push the cursor key or to highlight the new baudrate setting.

2Press ENTER to accept.

Reset Lamp Runtime

Reset lamp run time is only allowed when a new lamp is installed.

1Push the cursor key or to highlight 'Reset Lamp Runtime'.

2 Press ENTER to select.

When Reset Lamp Run Time is selected in the Service Mode selection menu, the following warning will be displayed :

Risk of electrical shock. Reset lamp run time is reserved to qualified service personnel.

If you are not qualified, press EXIT to cancel the reset operation.

SERVICE

 

 

 

IDENTIFICATION

 

 

 

CHANGE PASSWORD

 

 

 

CHANGE LANGUAGE

 

 

 

CHANGE PROJ. ADDRESS

 

 

 

CHANGE BAUDRATE PC

 

 

 

RESET LAMP RUNTIME

 

 

 

LAMP RUNTINE HISTORY

 

 

 

LAMP DRIVE MODE

 

 

 

MORE ...

 

 

 

then <ENTER>

 

 

 

<EXIT> to return.

 

 

 

CHANGE PROJ. ADDRESS

Enter new address

001

 

 

Select with

or

Reprogram with

or

or numeric keys

 

<ENTER>

to

confirm

<EXIT>

to

return

 

SERVICE

 

IDENTIFICATION

CHANGE PASSWORD

CHANGE LANGUAGE

CHANGE PROJ. ADDRESS

CHANGE BAUDRATE PC

RESET LAMP RUNTIME

LAMP RUNTINE HISTORY

LAMP DRIVE MODE : NORMAL

MORE...

Select with

or

then <ENTER>

<EXIT> to

return.

SERVICE

IDENTIFICATION

CHANGE PASSWORD

CHANGE LANGUAGE

CHANGE PROJ. ADDRESS

CHANGE BAUDRATE PC

RESET LAMP RUNTIME

LAMP RUNTINE HISTORY

LAMP DRIVE MODE

MORE

WARNING

Select

-----------------------------------------------------

RISK OF ELECTRICAL SHOCK

______________________________________________________________

RESET LAMP RUN TIME is reserved to

qualified

service personnel

<ENTER> to accept

<EXIT> to return.

10-4

 

5976052 BARCOREALITY 9300 070999

 

Page 49 Page 51
Image 50
Page 49 Page 51
Contents Reality 9300 DLC Federal communication commission FCC statement Barco Projection Systems Date Art. No 070999 R5976052Table of Contents Unpacking Unpacking and DimensionsProjector dimensions Battery installation in the RCU Installation Guidelines Componentvideo Where to install the projector?How to install a projection lens? Separate SyncFront Panel Terminology Control Panel Terminology a. Local keypadRemote control 175RCU Location and Functions of Control Configuration OSD Color ConfigurationInstallation FRONT/TABLE@-40 Projector Mode Communication Port Green Operation Installation Set Up Connections AC Power mains cord connectionSwitching on FusesLamp Run Time Switching to Stand-bySwitching Off Input ConnectionsInput Slots Peripheral Convergence Configuration Input SlotsFixed RGB analog input slot RGB-SOGRgbhv Rgbs Peripheral Convergence ConfigurationFixed 5-Input Slot slot VideoVideo/S-video Input Module 269,2VIDEO,1387RGB Analog Input Module Input Slots Component Input Module2032117B-Y S9,2,1387 16HSDRUP UD \ RGB3S / RG3sB Input ModuleSerial Digital Input slot 6HSDUDWH--6\QFV-VHOHFWLRQ\QFRQJUHHQConnecting a VS05 to the projector Set up of the Baud Rate for Communication with a ComputerConnecting a Rcvds 05 to the projector Connecting an IR Remote Receiver 800 to the projectorHow to Use the RCU? ControllingRCU Projector AddressPicture Controls with Direct Access How to Display a Projector Address?How to Program an Address into the RCU? Pause keyRandom Access Installation Service Start UP of the Adjustment ModeAdjustment Mode PasswordFile Service Random Access Adjustment ModeStarting up the Random Access Adjustment Mode Edit File File ServiceLoad File LoadOptions How to find the correct values for the displayed item?Read Amds Rename RenameField Polarity Copy CopyDelete DeleteFile Options Picture TuningColor Temperature File SortGamma GammaDecoding EBU/IRE Decoding EBUInput Balance Dynamic Color DepthNoise Reduction Dynamic Color DepthSize GeometryShift Side Keystone Side KeystoneBlanking BlankingShift Size Side Keystone Blanking OptionsBlanking TOP Bottom Left Right Starting up the Installation Mode Input SlotsPeripheral Output module selection How to AdjustTroubleshooting Infrared CommunicationBlue on Green convergence Green FocusingGreen to Midposition EnterAbout Moca Red on Green convergenceHatch Internal Patterns No Signal BLACK/BLUEOSD color On-Screen Display Service Service ModeStarting up the Service Mode Identification IdentificationSoftware version How to change the password ? Change PasswordHow to enable or disable the password function ? Service IdentificationChange Projector Address Reset Lamp RuntimeChange Language Change Baudrate PCBarco logo Lamp Drive ModeLamp Run Time History Uniformity Panel AdjustmentsPreset Input Balance I2C diagnosisStandard Source SET UP Files SUNXGA60 SUNEWS67SUNEWS76 SUNXGA70Cleaning procedure for HD1.5-31 lens Focusing the lensLens Cleaning Procedure LensesLenses Source numbers 90 Projector without any 800 peripheral connectedProjector with a 800 peripheral connected Source numbers 81 13875&966285&6
Top Page Image Contents