Barco R9001560 manual Lamp Run Time History, Lamp Drive Mode, Barco logo

Page 51

Service Mode

Lamp Run Time History

To get an overview of the different lamp run times :

1Push the cursor key or to highlight 'Lamp Run Time History'.

2Press ENTER to select.

A listing with the lamp serial number and the corresponding run time will be displayed.

The actual installed lamp will be marked.

Press EXIT to return to the service mode selection menu.

Lamp Drive Mode

The lamp can be driven in three different modes : SILENT, NORMAL or BOOST.

1Push the cursor key or to highlight 'Lamp Drive Mode'.

2 Press ENTER to select.

3Push the cursor key or to highlight the desired lamp drive mode.

4Press ENTER to select.

BARCO logo

The BARCO logo can be added to the image, in overlay or on a background, on any place on the screen.

To add the BARCO logo or to change a setting in the BARCO logo menu:

1Push the cursor key or to highlight 'BARCO logo'.

2 Press ENTER to select.

The BARCO logo menu will be displayed on the screen. Within this menu, three toggle settings and a shift control are available.

STATUS [ON/OFF]

ON : BARCO logo will be displayed on the screen.

OFF : No BARCO logo displayed on the screen.

BACKGROUND [ON/OFF]

ON : BARCO logo will be displayed on a black background.

OFF : BARCO logo will be displayed without any background.

SHIFT

By pushing the control disc up, down, to the left or to the right, the BARCO logo can be positioned anywhere on the screen.

HOT KEY [TEXT/OFF]

OFF : no key on the RCU is used to display the BARCO logo.

TEXT : the TEXT key on the RCU is used to display or to remove the BARCO logo with one single push on this key (only in operational :mode).

SERVICE

IDENTIFICATION

CHANGE PASSWORD

CHANGE LANGUAGE

CHANGE PROJ. ADDRESS

CHANGE BAUDRATE PC

RESET LAMP RUNTIME

LAMP RUNTINE HISTORY

LAMP DRIVE MODE

MORE...

Select with

or

 

then <ENTER> LAMP RUNTIME HISTORY

<EXIT> to

 

 

 

Serial No

Runtime

-----------------------------------------------------

>

0111121

600 h

 

0110031

980 h

 

0110010

1000 h

-----------------------------------------------------

 

<EXIT>

to return

SERVICE

IDENTIFICATION

CHANGEPASSWORD

CHANGE LANGUAGE

CHANGE PROJ. ADDRESS

CHANGE BAUDRATE PC

RESET LAMP RUNTIME

LAMP RUNTINE HISTORY

LAMP DRIVE MODE

LAMP DRIVE MODE

SILENT

NORMAL

BOOST

Select with

or

then <ENTER>

<EXIT> to

return.

SERVICE

BARCO LOGO

PANEL ADJUSTMENTS

UNIFORMITY

PRESET INPUT BALANCE

I2C DIAGNOSIS

MORE...

BARCO LOGO

STATUS : ON

BACKGROUND : ON

SHIFT

HOT KEY : TEXT

Select with or then <ENTER> <EXIT> to return.

5976052 BARCOREALITY 9300 070999

 

10-5

 

Image 51
Contents Reality 9300 DLC Federal communication commission FCC statement Date Art. No 070999 R5976052 Barco Projection SystemsTable of Contents Unpacking and Dimensions Projector dimensionsUnpacking Battery installation in the RCU Installation Guidelines Separate Sync Where to install the projector?How to install a projection lens? ComponentvideoControl Panel Terminology a. Local keypad Front Panel Terminology175 Remote controlRCU Location and Functions of Control FRONT/TABLE ConfigurationInstallation Configuration OSD Color@-40 Projector Mode Communication Port Green Operation Installation Set Up Fuses AC Power mains cord connectionSwitching on ConnectionsInput Connections Switching to Stand-bySwitching Off Lamp Run TimeRGB-SOG Peripheral Convergence Configuration Input SlotsFixed RGB analog input slot Input SlotsVideo Peripheral Convergence ConfigurationFixed 5-Input Slot slot Rgbhv Rgbs269,2VIDEO,1387 Video/S-video Input ModuleRGB Analog Input Module Component Input Module 2032117B-Y S9,2,1387Input Slots RGB3S / RG3sB Input Module 16HSDRUP UD \6HSDUDWH--6\QFV-VHOHFWLRQ\QFRQJUHHQ Serial Digital Input slotConnecting an IR Remote Receiver 800 to the projector Set up of the Baud Rate for Communication with a ComputerConnecting a Rcvds 05 to the projector Connecting a VS05 to the projectorControlling How to Use the RCU?Projector Address RCUPause key How to Display a Projector Address?How to Program an Address into the RCU? Picture Controls with Direct AccessPassword Start UP of the Adjustment ModeAdjustment Mode Random Access Installation ServiceRandom Access Adjustment Mode Starting up the Random Access Adjustment ModeFile Service Load File ServiceLoad File Edit FileHow to find the correct values for the displayed item? Read AmdsOptions Rename Field PolarityRename Delete CopyDelete CopyFile Sort Picture TuningColor Temperature File OptionsDecoding EBU GammaDecoding EBU/IRE GammaDynamic Color Depth Dynamic Color DepthNoise Reduction Input BalanceGeometry ShiftSize Blanking Side KeystoneBlanking Side KeystoneOptions Blanking TOP Bottom Left RightShift Size Side Keystone Blanking Input Slots Starting up the Installation ModeInfrared Communication How to AdjustTroubleshooting Peripheral Output module selectionEnter Green FocusingGreen to Midposition Blue on Green convergenceRed on Green convergence HatchAbout Moca No Signal BLACK/BLUE OSD color On-Screen DisplayInternal Patterns Service Mode Starting up the Service ModeService Identification Software versionIdentification Service Identification Change PasswordHow to enable or disable the password function ? How to change the password ?Change Baudrate PC Reset Lamp RuntimeChange Language Change Projector AddressLamp Drive Mode Lamp Run Time HistoryBarco logo I2C diagnosis Panel AdjustmentsPreset Input Balance UniformityStandard Source SET UP Files SUNXGA70 SUNEWS67SUNEWS76 SUNXGA60Lenses Focusing the lensLens Cleaning Procedure Cleaning procedure for HD1.5-31 lensLenses Projector without any 800 peripheral connected Projector with a 800 peripheral connectedSource numbers 90 Source numbers 81 13875&966285&6