Barco R9001560 manual Green to Midposition, Green Focusing, Blue on Green convergence, Enter

Page 44

Installation Mode

Green to Midposition

Only in case all panels have been removed and replaced by others or when the convergence is totally misaligned.

For normal convergence adjustment, this step can be skipped.

To set Green in Midposition :

1Push the cursor key or  to highlight 'Green to midposition'.

2 Press ENTER to select.

A warning will be displayed :

"Are you sure to set the green motorized convergence adjustment to midposition ? This adjustment cannot be undone afterwards !".

3If you are sure, press ENTER to continue, otherwise press EDIT to cancel.

Remark : While 'Green to midposition' is in progress, a clicking sound may be heard, caused by the end of adjustment motor protection.

Green Focusing

1Highlight 'Green' by pushing the cursor key or  and press

ENTER

2Adjust the projection lens until optimal focus on position 3 is obtained.

hint : use the focusing marker lines next to the digit.

3Adjust position 1 for optimal focus.

4 Adjust position 2 for optimal focus.

5 Adjust position 3 for optimal focus.

6Repeat step 3, 4 and 5 one time as these three alignments influence each other slightly.

Blue on Green convergence

1Highlight 'Blue on Green' by pushing the cursor key or and press ENTER to display the Blue on green test pattern. The drawings and digits will be displayed in blue.

2Adjust position 1, 2 and 3 to obtain an optimal focus for these lines.

3Due to interaction, it will be necessary to repeat step2.

4Adjust position 4 and 5 for optimal convergence of the lines in 4 and 5.

5Adjust position 6 for optimal convergence of the vertical lines in 6.

6Check if all lines are correctly converged.

CONVERGENCE

GREEN TO MIDPOSITION

GREEN

BLUE ON GREEN

RED ON GREEN

HATCH

ABOUT MOCA

GREEN TO MIDPOSITION

Are you sure to set the green motorized convergence adjustment to midposition ?

This adjustment cannot be undone afterwards !

<ENTER> to continue

<EXIT> to cancel

CONVERGENCE
GREEN TO MIDPOSITION
GREEN
BLUE ON GREEN
RED ON GREEN
HATCH
ABOUT MOCA
Select with	or
then <ENTER>
<EXIT> to return.

CONVERGENCE
GREEN TO MIDPOSITION
GREEN
BLUE ON GREEN
RED ON GREEN
HATCH
ABOUT MOCA
Select with	or
then <ENTER>
<EXIT> to return.

9-3		5976052 BARCOREALITY 9300 070999

Image 44

Contents Reality 9300 DLC Federal communication commission FCC statement Barco Projection Systems Date Art. No 070999 R5976052Table of Contents Unpacking Unpacking and DimensionsProjector dimensions Battery installation in the RCU Installation Guidelines Where to install the projector? How to install a projection lens?Componentvideo Separate SyncFront Panel Terminology Control Panel Terminology a. Local keypadRemote control 175RCU Location and Functions of Control Configuration InstallationConfiguration OSD Color FRONT/TABLE@-40 Projector Mode Communication Port Green Operation Installation Set Up AC Power mains cord connection Switching onConnections FusesSwitching to Stand-by Switching OffLamp Run Time Input ConnectionsPeripheral Convergence Configuration Input Slots Fixed RGB analog input slotInput Slots RGB-SOGPeripheral Convergence Configuration Fixed 5-Input Slot slotRgbhv Rgbs VideoVideo/S-video Input Module 269,2VIDEO,1387RGB Analog Input Module Input Slots Component Input Module2032117B-Y S9,2,1387 16HSDRUP UD \ RGB3S / RG3sB Input ModuleSerial Digital Input slot 6HSDUDWH--6\QFV-VHOHFWLRQ\QFRQJUHHQSet up of the Baud Rate for Communication with a Computer Connecting a Rcvds 05 to the projectorConnecting a VS05 to the projector Connecting an IR Remote Receiver 800 to the projectorHow to Use the RCU? ControllingRCU Projector AddressHow to Display a Projector Address? How to Program an Address into the RCU?Picture Controls with Direct Access Pause keyStart UP of the Adjustment Mode Adjustment ModeRandom Access Installation Service PasswordFile Service Random Access Adjustment ModeStarting up the Random Access Adjustment Mode File Service Load FileEdit File LoadOptions How to find the correct values for the displayed item?Read Amds Rename RenameField Polarity Copy DeleteCopy DeletePicture Tuning Color TemperatureFile Options File SortGamma Decoding EBU/IREGamma Decoding EBUDynamic Color Depth Noise ReductionInput Balance Dynamic Color DepthSize GeometryShift Side Keystone BlankingSide Keystone BlankingShift Size Side Keystone Blanking OptionsBlanking TOP Bottom Left Right Starting up the Installation Mode Input SlotsHow to Adjust TroubleshootingPeripheral Output module selection Infrared CommunicationGreen Focusing Green to MidpositionBlue on Green convergence EnterAbout Moca Red on Green convergenceHatch Internal Patterns No Signal BLACK/BLUEOSD color On-Screen Display Service Service ModeStarting up the Service Mode Identification IdentificationSoftware version Change Password How to enable or disable the password function ?How to change the password ? Service IdentificationReset Lamp Runtime Change LanguageChange Projector Address Change Baudrate PCBarco logo Lamp Drive ModeLamp Run Time History Panel Adjustments Preset Input BalanceUniformity I2C diagnosisStandard Source SET UP Files SUNEWS67 SUNEWS76SUNXGA60 SUNXGA70Focusing the lens Lens Cleaning ProcedureCleaning procedure for HD1.5-31 lens LensesLenses Source numbers 90 Projector without any 800 peripheral connectedProjector with a 800 peripheral connected Source numbers 81 13875&966285&6