Barco R9001560 manual Identification, Software version

Page 48

Service Mode

SERVICE

IDENTIFICATION

CHANGE PASSWORD CHANGE LANGUAGE CHANGE PROJ. ADDRESS CHANGE BAUDRATE PC RESET LAMP RUNTIME LAMP RUNTINE HISTORY LAMP DRIVE MODE MORE...

Select with or then <ENTER> <EXIT> to return.

PANEL ADJUSTMENT

Select the

color temperature

PROJECTOR WHITE

6500

Select with or then <ENTER> <EXIT> to return.

PRESET INPUT BALANCE

WHITE BALANCE

BLACK BALANCE

DEFAULT

Select with <ENTER>

<EXIT> to return

Adjust

red with or

blue with or

UNIFORMITY

ADJUST

PURITY

DEFAULT

Select with or then <ENTER> <EXIT> to return.

SERVICE

BARCO LOGO

PANEL ADJUSTMENTS

UNIFORMITY

PRESET INPUT BALANCE

I2C DIAGNOSIS

MORE...

Select with or then <ENTER> <EXIT> to return.

BARCO LOGO

STATUS : [ON]

BACKGROUND : [ON]

SHIFT

HOT KEY : [TEXT]

Select with or <ENTER> to toggle/select <EXIT> to return.

I2C DIAGNOSIS

 

 

 

 

 

D CA

LCD DRIVER

SC76013

E4H # # #

LCD DRIVER

SC76013

E6H # # #

LCD DRIVER

SC76013

E8H # # #

LCD DRIVER

SC76013

EAH # # #

INPUT SELECT

TDA8444

46H

# # #

INPUT SELECT

PCF8574A 7EH # # #

DECODER

87C751

12H

# # #

LAMP DRIVER

PCF8574A

72H

# # #

POWER SUPPLY 87C752

10H

# # #

Identification

To display the Identification screen:

1Push the cursor key or to highlight 'Identification'.

2 Press ENTER to display the Identification screen.

The Identification screen gives an overview of :

-type of projector

-projector address

-software version

-installation configuration

-baud rate

-text ON

-projector serial number

-projector run time

-type of projector : BARCOREALITY 9300DLC

-software version

-Proj. Address : to change the address of the projector, see Change Projector Address in this chapter.

-Installation : possible installations :

*Front/Ceiling

*Front/Table

*Rear/Ceiling

*Rear/Table

To change the installation configuration follow the instructions in chapter Installation Set Up.

-Baud rate : transfer speed for communication with an IBM PC (or compatible) or MAC. The baud rate of the projector must be the same as the baud rate of the connected computer. When there is a difference, consult 'Change Baudrate PC' in this chapter.

-Projector Run Time : gives the total run time since the first start up. All projectors leave the factory with a run time of approximately 24 hours.

-Projector Serial number : indicates the fabrication number of the projector. This number can be useful when calling for technical assistance.

SERVICE

IDENTIFICATION

CHANGE PASSWORD CHANGE LANGUAGE

CHANGE PROJ. ADDRESS CHANGE BAUDRATE PC RESET LAMP RUNTIME LAMP RUNTINE HISTORY

LAMP DRIVE MODE

MORE...

Select with or then <ENTER> <EXIT> to return.

10-2

 

5976052 BARCOREALITY 9300 070999

 

Page 47 Page 49
Image 48
Page 47 Page 49
Contents Reality 9300 DLC Federal communication commission FCC statement Barco Projection Systems Date Art. No 070999 R5976052Table of Contents Unpacking and Dimensions Projector dimensionsUnpacking Battery installation in the RCU Installation Guidelines Where to install the projector? How to install a projection lens?Componentvideo Separate SyncFront Panel Terminology Control Panel Terminology a. Local keypadRemote control 175RCU Location and Functions of Control Configuration InstallationConfiguration OSD Color FRONT/TABLE@-40 Projector Mode Communication Port Green Operation Installation Set Up AC Power mains cord connection Switching onConnections FusesSwitching to Stand-by Switching OffLamp Run Time Input ConnectionsPeripheral Convergence Configuration Input Slots Fixed RGB analog input slotInput Slots RGB-SOGPeripheral Convergence Configuration Fixed 5-Input Slot slotRgbhv Rgbs VideoVideo/S-video Input Module 269,2VIDEO,1387RGB Analog Input Module Component Input Module 2032117B-Y S9,2,1387Input Slots 16HSDRUP UD \ RGB3S / RG3sB Input ModuleSerial Digital Input slot 6HSDUDWH--6\QFV-VHOHFWLRQ\QFRQJUHHQSet up of the Baud Rate for Communication with a Computer Connecting a Rcvds 05 to the projectorConnecting a VS05 to the projector Connecting an IR Remote Receiver 800 to the projectorHow to Use the RCU? ControllingRCU Projector AddressHow to Display a Projector Address? How to Program an Address into the RCU?Picture Controls with Direct Access Pause keyStart UP of the Adjustment Mode Adjustment ModeRandom Access Installation Service PasswordRandom Access Adjustment Mode Starting up the Random Access Adjustment ModeFile Service File Service Load FileEdit File LoadHow to find the correct values for the displayed item? Read AmdsOptions Rename Field PolarityRename Copy DeleteCopy DeletePicture Tuning Color TemperatureFile Options File SortGamma Decoding EBU/IREGamma Decoding EBUDynamic Color Depth Noise ReductionInput Balance Dynamic Color DepthGeometry ShiftSize Side Keystone BlankingSide Keystone BlankingOptions Blanking TOP Bottom Left RightShift Size Side Keystone Blanking Starting up the Installation Mode Input SlotsHow to Adjust TroubleshootingPeripheral Output module selection Infrared CommunicationGreen Focusing Green to MidpositionBlue on Green convergence EnterRed on Green convergence HatchAbout Moca No Signal BLACK/BLUE OSD color On-Screen DisplayInternal Patterns Service Mode Starting up the Service ModeService Identification Software versionIdentification Change Password How to enable or disable the password function ?How to change the password ? Service IdentificationReset Lamp Runtime Change LanguageChange Projector Address Change Baudrate PCLamp Drive Mode Lamp Run Time HistoryBarco logo Panel Adjustments Preset Input BalanceUniformity I2C diagnosisStandard Source SET UP Files SUNEWS67 SUNEWS76SUNXGA60 SUNXGA70Focusing the lens Lens Cleaning ProcedureCleaning procedure for HD1.5-31 lens LensesLenses Projector without any 800 peripheral connected Projector with a 800 peripheral connectedSource numbers 90 Source numbers 81 13875&966285&6
Top Page Image Contents