Barco R9001560 manual Dynamic Color Depth, Noise Reduction, Input Balance

Page 38

Random Access Adjustment Mode

Dynamic Color Depth

Increases color contrast for all video and data sources. To change the dynamic color depth value :

1Push the cursor key or to highlight 'Dynamic Color Depth'.

2 Press ENTER to select.

3 Change the value by pushing the cursor key or until the desired color contrast is reached.

Adjustment range : 0 ... 8

Default : 4

4 Press EXIT to return to the Picture Tuning menu.

Noise Reduction

Reduces noise and pixel jitter in all video and data sources.

To change the noise reduction value :

1Push the cursor key or to highlight 'Noise Reduction'.

2 Press ENTER to select.

3 Change the value by pushing the cursor key or until the desired noise level is reached.

Adjustment range : 0 ... 8

4 Press EXIT to return to the Picture Tuning menu.

PICTURE TUNING

CTI [ON]

COLOR TEMPERATURE

GAMMA

DECODING [EBU]

DYNAMIC COLOR DEPTH

NOISE REDUCTION

INPUT BALANCE

Select with or then <ENTER> <EXIT> to return.

DYNAMIC COLOR DEPTH 4

08

PICTURE TUNING

CTI [ON]

COLOR TEMPERATURE

GAMMA

DECODING [EBU]

DYNAMIC COLOR DEPTH

NOISE REDUCTION

INPUT BALANCE

Select with or then <ENTER> <EXIT> to return.

 

NOISE REDUCTION

0

8

Input Balance

The input balance is normally correct adjusted in the factory. But due to signal distribution or signal transmission, a color imbalance can be the result. This imbalance can be adjusted source by source for color critical applications. These adjustments influence only the actual custom adjustment file. This procedure is not so easy

.

Attention : Before starting the Input Balance function, generate a signal with dominant black and white areas.

The default values are normally loaded when selecting a source. If the image is not as desired, adjust for this source as follow :

Start with the Black Balance :

1Push the cursor key or to highlight 'Black Balance'.

2 Press ENTER to select.

3 Put the Black Balance Red and Blue to -32

4 Adjust the Brightness to a maximum value until there is just no green noise visible in the black areas.

5 Adjust with the cursor key or or or until there is just no red or blue noise visible in the black areas.

Continue with the White Balance :

1Push the cursor key or to highlight 'White Balance'.

2 Press ENTER to select.

3 Put the Gain Red and the Gain Blue to -32.

4 Adjust the Contrast to a maximum value until the green noise becomes visible in the white areas and return one step.

5 Adjust with the cursor key or or or until the red respectively blue noise becomes visible in the white areas and return one step.

PICTURE TUNING

 

 

CTI [ON]

 

 

COLOR TEMPERATURE

 

GAMMA

 

 

DECODING [EBU]

 

 

DYNAMIC COLOR DEPTH

 

NOISE REDUCTION

 

 

INPUT BALANCE

 

 

then <ENTER>

 

 

<EXIT> to

INPUT BALANCE

 

 

WHITE BALANCE

 

BLACK BALANCE

 

DEFAULT

 

 

ADJUST

 

 

RED WITH

OR

 

BLUE WITH

OR

8-8

 

5976052 BARCOREALITY 9300 070999

 

Image 38
Contents Reality 9300 DLC Federal communication commission FCC statement Barco Projection Systems Date Art. No 070999 R5976052Table of Contents Unpacking Unpacking and DimensionsProjector dimensions Battery installation in the RCU Installation Guidelines Componentvideo Where to install the projector?How to install a projection lens? Separate SyncFront Panel Terminology Control Panel Terminology a. Local keypadRemote control 175RCU Location and Functions of Control Configuration OSD Color ConfigurationInstallation FRONT/TABLE@-40 Projector Mode Communication Port Green Operation Installation Set Up Connections AC Power mains cord connectionSwitching on FusesLamp Run Time Switching to Stand-bySwitching Off Input ConnectionsInput Slots Peripheral Convergence Configuration Input SlotsFixed RGB analog input slot RGB-SOGRgbhv Rgbs Peripheral Convergence ConfigurationFixed 5-Input Slot slot VideoVideo/S-video Input Module 269,2VIDEO,1387RGB Analog Input Module Input Slots Component Input Module2032117B-Y S9,2,1387 16HSDRUP UD \ RGB3S / RG3sB Input ModuleSerial Digital Input slot 6HSDUDWH--6\QFV-VHOHFWLRQ\QFRQJUHHQConnecting a VS05 to the projector Set up of the Baud Rate for Communication with a ComputerConnecting a Rcvds 05 to the projector Connecting an IR Remote Receiver 800 to the projectorHow to Use the RCU? ControllingRCU Projector AddressPicture Controls with Direct Access How to Display a Projector Address?How to Program an Address into the RCU? Pause keyRandom Access Installation Service Start UP of the Adjustment ModeAdjustment Mode PasswordFile Service Random Access Adjustment ModeStarting up the Random Access Adjustment Mode Edit File File ServiceLoad File LoadOptions How to find the correct values for the displayed item?Read Amds Rename RenameField Polarity Copy CopyDelete DeleteFile Options Picture TuningColor Temperature File SortGamma GammaDecoding EBU/IRE Decoding EBUInput Balance Dynamic Color DepthNoise Reduction Dynamic Color DepthSize GeometryShift Side Keystone Side KeystoneBlanking BlankingShift Size Side Keystone Blanking OptionsBlanking TOP Bottom Left Right Starting up the Installation Mode Input SlotsPeripheral Output module selection How to AdjustTroubleshooting Infrared CommunicationBlue on Green convergence Green FocusingGreen to Midposition EnterAbout Moca Red on Green convergenceHatch Internal Patterns No Signal BLACK/BLUEOSD color On-Screen Display Service Service ModeStarting up the Service Mode Identification IdentificationSoftware version How to change the password ? Change PasswordHow to enable or disable the password function ? Service IdentificationChange Projector Address Reset Lamp RuntimeChange Language Change Baudrate PCBarco logo Lamp Drive ModeLamp Run Time History Uniformity Panel AdjustmentsPreset Input Balance I2C diagnosisStandard Source SET UP Files SUNXGA60 SUNEWS67SUNEWS76 SUNXGA70Cleaning procedure for HD1.5-31 lens Focusing the lensLens Cleaning Procedure LensesLenses Source numbers 90 Projector without any 800 peripheral connectedProjector with a 800 peripheral connected Source numbers 81 13875&966285&6