Barco R9001560 manual Gamma, Decoding EBU/IRE

Page 37

Random Access Adjustment Mode

Custom balance allows the user to set his own prefered color temperature.

To adjust Custom Balance, handle as follow :

1Push the cursor key or to highlight 'Custom Balance'.

2 Press ENTER to select.

3 Push the cursor key or to adjust red and push the cursor key or to adjust blue (range 0 to 2.5) in comparison with the green color (value 1).

Gamma

With the gamma correction adjustment, it is possible to accurately set the gamma of the projector image.

To change the gamma value :

1Push the cursor key or to highlight 'Gamma'.

2 Press ENTER to select.

3 Change the gamma value by pushing the cursor key or until the desired value is reached.

4 Press EXIT to return to the Picture Tuning menu.

Default value for gamma = 2.2

Decoding EBU/IRE

Only for NTSC signals.

The possibility is offered to decode the NTSC video signals via the default American IRE standard or via the European EBU standard. Decoding a NTSC signal using the European EBU standard may result in a greenish tint.

1Push the cursor key or to highlight 'Decoding'.

2 Press ENTER to toggle between EBU or IRE.

3 Press EXIT to return.

CUSTOM COLOR BALANCE

CUSTOM WHITE BALANCE

Select with <ENTER>

<EXIT> to

return.

ADJUST

RED WITH

OR

BLUE WITH

OR

 

GAIN RED

0

2.5

PICTURE TUNING

CTI [ON]

COLOR TEMPERATURE

GAMMA

DECODING [EBU]

DYNAMIC COLOR DEPTH

NOISE REDUCTION

INPUT BALANCE

GAMMA = 2.2

3

PICTURE TUNING

CTI [ON]

COLOR TEMPERATURE

GAMMA

DECODING [EBU]

DYNAMIC COLOR DEPTH

NOISE REDUCTION

INPUT BALANCE

Select with

or

then <ENTER>

<EXIT> to

return.

5976052 BARCOREALITY 9300 070999

 

8-7

 

Image 37
Contents Reality 9300 DLC Federal communication commission FCC statement Date Art. No 070999 R5976052 Barco Projection SystemsTable of Contents Projector dimensions Unpacking and DimensionsUnpacking Battery installation in the RCU Installation Guidelines How to install a projection lens? Where to install the projector?Componentvideo Separate SyncControl Panel Terminology a. Local keypad Front Panel Terminology175 Remote controlRCU Location and Functions of Control Installation ConfigurationConfiguration OSD Color FRONT/TABLE@-40 Projector Mode Communication Port Green Operation Installation Set Up Switching on AC Power mains cord connectionConnections FusesSwitching Off Switching to Stand-byLamp Run Time Input ConnectionsFixed RGB analog input slot Peripheral Convergence Configuration Input SlotsInput Slots RGB-SOGFixed 5-Input Slot slot Peripheral Convergence ConfigurationRgbhv Rgbs Video269,2VIDEO,1387 Video/S-video Input ModuleRGB Analog Input Module 2032117B-Y S9,2,1387 Component Input ModuleInput Slots RGB3S / RG3sB Input Module 16HSDRUP UD \6HSDUDWH--6\QFV-VHOHFWLRQ\QFRQJUHHQ Serial Digital Input slotConnecting a Rcvds 05 to the projector Set up of the Baud Rate for Communication with a ComputerConnecting a VS05 to the projector Connecting an IR Remote Receiver 800 to the projectorControlling How to Use the RCU?Projector Address RCUHow to Program an Address into the RCU? How to Display a Projector Address?Picture Controls with Direct Access Pause keyAdjustment Mode Start UP of the Adjustment ModeRandom Access Installation Service PasswordStarting up the Random Access Adjustment Mode Random Access Adjustment ModeFile Service Load File File ServiceEdit File LoadRead Amds How to find the correct values for the displayed item?Options Field Polarity RenameRename Delete CopyCopy DeleteColor Temperature Picture TuningFile Options File SortDecoding EBU/IRE GammaGamma Decoding EBUNoise Reduction Dynamic Color DepthInput Balance Dynamic Color DepthShift GeometrySize Blanking Side KeystoneSide Keystone BlankingBlanking TOP Bottom Left Right OptionsShift Size Side Keystone Blanking Input Slots Starting up the Installation ModeTroubleshooting How to AdjustPeripheral Output module selection Infrared CommunicationGreen to Midposition Green FocusingBlue on Green convergence EnterHatch Red on Green convergenceAbout Moca OSD color On-Screen Display No Signal BLACK/BLUEInternal Patterns Starting up the Service Mode Service ModeService Software version IdentificationIdentification How to enable or disable the password function ? Change PasswordHow to change the password ? Service IdentificationChange Language Reset Lamp RuntimeChange Projector Address Change Baudrate PCLamp Run Time History Lamp Drive ModeBarco logo Preset Input Balance Panel AdjustmentsUniformity I2C diagnosisStandard Source SET UP Files SUNEWS76 SUNEWS67SUNXGA60 SUNXGA70Lens Cleaning Procedure Focusing the lensCleaning procedure for HD1.5-31 lens LensesLenses Projector with a 800 peripheral connected Projector without any 800 peripheral connectedSource numbers 90 Source numbers 81 13875&966285&6