Texas Instruments TMS320x28xx, 28xxx Time-Base Submodule Registers, Bits Name Value Description

Page 94

www.ti.com

Time-Base Submodule Registers

4.1Time-Base Submodule Registers

Figure 4-1through Figure 4-5and Table 4-1through Table 4-5provide the time-base register definitions.

Figure 4-1. Time-Base Period Register (TBPRD)

15

0

TBPRD

R/W-0

LEGEND: R/W = Read/Write; R = Read only; -n = value after reset

 

Table 4-1. Time-Base Period Register (TBPRD) Field Descriptions

Bits Name

Value Description

15-0 TBPRD 0000-

FFFF

These bits determine the period of the time-base counter. This sets the PWM frequency.

Shadowing of this register is enabled and disabled by the TBCTL[PRDLD] bit. By default this register is shadowed.

∙If TBCTL[PRDLD] = 0, then the shadow is enabled and any write or read will automatically go to the shadow register. In this case, the active register will be loaded from the shadow register when the time-base counter equals zero.

∙If TBCTL[PRDLD] = 1, then the shadow is disabled and any write or read will go directly to the active register, that is the register actively controlling the hardware.

∙The active and shadow registers share the same memory map address.

 

Figure 4-2. Time-Base Phase Register (TBPHS)

15

0

TBPHS

R/W-0

LEGEND: R/W = Read/Write; R = Read only; -n = value after reset

 

 

Table 4-2. Time-Base Phase Register (TBPHS) Field Descriptions

Bits

Name

Value Description

15-0

TBPHS

0000- These bits set time-base counter phase of the selected ePWM relative to the time-base that is

FFFFsupplying the synchronization input signal.

∙If TBCTL[PHSEN] = 0, then the synchronization event is ignored and the time-base counter is not loaded with the phase.

∙If TBCTL[PHSEN] = 1, then the time-base counter (TBCTR) will be loaded with the phase (TBPHS) when a synchronization event occurs. The synchronization event can be initiated by the input synchronization signal (EPWMxSYNCI) or by a software forced synchronization.

Figure 4-3. Time-Base Counter Register (TBCTR)

15

0

TBCTR

R/W-0

LEGEND: R/W = Read/Write; R = Read only; -n = value after reset

 

 

Table 4-3. Time-Base Counter Register (TBCTR) Field Descriptions

Bits

Name

Value Description

15-0

TBCTR

0000- Reading these bits gives the current time-base counter value.

 

 

FFFF

Writing to these bits sets the current time-base counter value. The update happens as soon as the write occurs; the write is NOT synchronized to the time-base clock (TBCLK) and the register is not shadowed.

94

Registers

SPRU791D–November 2004–Revised October 2007

Page 93 Page 95
Image 94
Page 93 Page 95
Contents Reference Guide Submit Documentation Feedback Contents Controlling a 3-Phase Interleaved DC/DC Converter List of Figures Event-Trigger Socb Pulse Generator Simplified ePWM Module List of Tables Submit Documentation Feedback CPU Users Guides Related Documentation From Texas InstrumentsData Manuals Peripheral GuidesTools Guides Application ReportsTrademarks TMS320C28x, C28x are trademarks of Texas InstrumentsSubmit Documentation Feedback Introduction Introduction Submodule OverviewMultiple ePWM Modules ∙ ADC start-of-conversion signals EPWMxSOCA and EPWMxSOCB ∙ PWM output signals EPWMxA and EPWMxB∙ Trip-zone signals TZ1 to TZ6 ∙ Peripheral BusEPWM Submodules and Critical Internal Signal Interconnects Register MappingTime-Base Submodule Registers Offset Size NameDescription Counter-Compare Submodule RegistersEPWM Submodules Submodule Configuration Parameter or Option Submodule Configuration ParametersOverview Example 2-1. Constant Definitions Used in the Code Examples TbupChpenable Time-Base TB Submodule Purpose of the Time-Base SubmoduleTime-Base Submodule Registers Controlling and Monitoring the Time-base SubmoduleRegister ∙ Up-Count Mode Key Time-Base Signals∙ Up-Down-Count Mode ∙ Down-Count ModeTime-Base Period Shadow Register ∙ Time-Base Period Shadow Mode∙ Time-Base Period Immediate Load Mode ∙ Active RegisterTime-Base Counter Synchronization Time-Base Counter Synchronization SchemeEPWM11SYNCI EPWM11SYNCO∙ EPWMxSYNCI Synchronization Input Pulse ∙ Software Forced Synchronization PulsePhase Locking the Time-Base Clocks of Multiple ePWM Modules Time-base Counter Modes and Timing WaveformsTime-Base Down-Count Mode Waveforms Counter-Compare CC Submodule 11. Counter-Compare SubmoduleCounter-Compare Submodule Registers Purpose of the Counter-Compare SubmoduleControlling and Monitoring the Counter-Compare Submodule Register Name Address Offset∙ Shadow Mode Count Mode Timing WaveformsCounter-Compare Submodule Key Signals ∙ Immediate Load ModeCTR=CMPA CTR=CMPBCTR = Cmpb Purpose of the Action-Qualifier Submodule Action-Qualifier AQ SubmoduleAction-Qualifier Submodule Registers ∙ Clear Low Action-Qualifier Submodule Possible Input Events∙ Set High ∙ ToggleTB Counter equals Actions 10. Action-Qualifier Event Priority for Down-Count Mode Action-Qualifier Event Priority for Up-Down-Count ModeAction-Qualifier Event Priority for Up-Count Mode Action-Qualifier Event PriorityUse up-down-count mode to generate an asymmetric PWM Waveforms for Common ConfigurationsUse up-down-count mode to generate a symmetric PWM When using up-count mode to generate an asymmetric PWM20. Up-Down-Count Mode Symmetrical Waveform Example 2-2. Code Sample for Figure TbctrValue EPWMxA EPWMxB Example 2-3. Code Sample for Figure Tbclk = SysclkoutExample 2-4. Code Sample for Figure EdgePosAExample 2-5. Code Sample for Figure Example 2-6. Code Sample for Figure TbctrExample 2-7. Code Sample for Figure EPWMxA EPWMxBControlling and Monitoring the Dead-Band Submodule Dead-Band Generator DB SubmodulePurpose of the Dead-Band Submodule 12. Dead-Band Generator Submodule Registers∙ Input Source Selection ∙ Output Mode ControlOperational Highlights for the Dead-Band Submodule ∙ Polarity ControlMode Description 13. Classical Dead-Band Operating Modes29. Dead-Band Waveforms for Typical Cases 0% Duty 100% Dead-Band Delay in μS FED = Dbfed × Ttbclk RED = Dbred × TtbclkControlling the PWM-Chopper Submodule PWM-Chopper PC SubmodulePurpose of the PWM-Chopper Submodule Operational Highlights for the PWM-Chopper SubmoduleWaveforms 31. PWM-Chopper Submodule Operational Details16. Possible Pulse Width Values for Sysclkout = 100 MHz One-Shot PulseOSHTWTHz Duty Cycle Control PeriodTrip-Zone TZ Submodule Purpose of the Trip-Zone Submodule17. Trip-Zone Submodule Registers Controlling and Monitoring the Trip-Zone SubmoduleOperational Highlights for the Trip-Zone Submodule ∙ Cycle-by-Cycle CBCScenario a Example 2-8. Trip-Zone Configurations18. Possible Actions On a Trip Event Scenario B36. Trip-Zone Submodule Mode Control Logic Generating Trip Event InterruptsEvent-Trigger ET Submodule 37. Trip-Zone Submodule Interrupt LogicOperational Overview of the Event-Trigger Submodule 19. Event-Trigger Submodule Registers CTR=CMPB CTRD=CMPB41. Event-Trigger Interrupt Generator 42. Event-Trigger Soca Pulse Generator Submit Documentation Feedback Applications to Power Topologies Controlling Multiple Buck Converters With IndependentKey Configuration Capabilities Overview of Multiple ModulesCTR=0 EPWM1B CTR=CMPB Control of Four Buck Stages. Here FPWM1≠ FPWM2≠ FPWM3≠ FPWM4 Buck Waveforms for -3Note Only three bucks shown here Example 3-1. Configuration for Example in Figure 500Controlling Multiple Buck Converters With Same Frequencies Control of Four Buck Stages. Note FPWM2 = N x FPWM1Buck Waveforms for -5Note FPWM2 = FPWM1 Example 3-2. Code Snippet for Configuration in Figure Controlling Multiple Half H-Bridge HHB Converters Control of Two Half-H Bridge Stages FPWM2 = N x FPWM1Half-H Bridge Waveforms for -7Note Here FPWM2 = FPWM1 Controlling Dual 3-Phase Inverters for Motors ACI and Pmsm Example 3-3. Code Snippet for Configuration in FigureEPWM1A 10 -Phase Inverter Waveforms for -9Only One Inverter Shown Example 3-4. Code Snippet for Configuration in Figure 11. Configuring Two PWM Modules for Phase Control Controlling a 3-Phase Interleaved DC/DC Converter Controlling a 3-Phase Interleaved DC/DC Converter13. Control of a 3-Phase Interleaved DC/DC Converter 14 -Phase Interleaved DC/DC Converter Waveforms for Figure Example 3-5. Code Snippet for Configuration in Figure 15. Controlling a Full-H Bridge Stage FPWM2 = FPWM1 16. ZVS Full-H Bridge Waveforms Example 3-6. Code Snippet for Configuration in Figure Submit Documentation Feedback PWM-Chopper Submodule Control Register Proper Interrupt Initialization ProcedureTrip-Zone Submodule Control and Status Registers Time-Base Period Register Tbprd Field Descriptions Time-Base Phase Register Tbphs Field DescriptionsTime-Base Submodule Registers Time-Base Counter Register Tbctr Field DescriptionsTime-Base Control Register Tbctl Field Descriptions Bit Field Value DescriptionSoftware Forced Synchronization Pulse Time-Base Status Register Tbsts Field Descriptions Counter-Compare Submodule RegistersBit Field Counter-Compare B Register Cmpb Field Descriptions Counter-Compare a Register Cmpa Field DescriptionsBits Name Description Action-Qualifier Submodule Registers Counter-Compare Control Register Cmpctl Field DescriptionsBits Name CBD CBU CAD CAU PRD ZROCBD 10. Action-Qualifier Output B Control Register Aqctlb Rldcsf Rldcsf Otsfb Actsfb Otsfa ActsfaCsfb Csfa Csfb Dead-Band Submodule RegistersInmode Polsel Outmode Inmode Name Value Description PWM-Chopper Submodule Control Register16. PWM-Chopper Control Register Pcctl Bit Descriptions ReservedPWM-Chopper Control Register Pcctl Bit Descriptions Trip-Zone Submodule Control and Status RegistersChpduty OSHT6 OSHT6 OSHT5 OSHT4 OSHT3 OSHT2 OSHT1CBC6 CBC5 CBC4 CBC3 CBC2 CBC1 CBC6TZB 18. Trip-Zone Control Register Tzctl Field DescriptionsTZB TZA OST CBC20. Trip-Zone Flag Register Tzflg Field Descriptions OST CBC INT21. Trip-Zone Clear Register Tzclr Field Descriptions Event-Trigger Submodule Registers22. Trip-Zone Force Register Tzfrc Field Descriptions 23. Event-Trigger Selection Register Etsel 24. Event-Trigger Prescale Register Etps Field Descriptions Name Description24. Event-Trigger Prescale Register Etps Field Descriptions Socb Soca26. Event-Trigger Clear Register Etclr Field Descriptions 25. Event-Trigger Flag Register Etflg Field DescriptionsSocb Proper Interrupt Initialization Procedure 27. Event-Trigger Force Register Etfrc Field Descriptions116 Table A-1. Changes for Revision D Location Modifications, Additions, and DeletionsAppendix a Important Notice
Top Page Image Contents