SMC Networks EX500 manual ・Safety instructions for pneumatic equipment, ・Level of potential hazard

Page 2

EX500 Serial System

EX## - OME0008

● Safety Instructions ●

( Read carefully before handling. )

Thoroughly read this handling manual and related manuals mentioned here to ensure the safety and proper operation of the product.

These safety instructions are intended to prevent hazardous situations and / or equipment damage. These instructions indicate the level of potential hazard by labeling “ CAUTION “ or “ WARNING“ .

・Level of potential hazard

!CAUTION : Operator error could result in injury or equipment damage.

!WARNING : Operator error could result in serious injury or loss of life .

・Safety instructions for pneumatic equipment

！WARNING

1.The compatibility of pneumatic equipment is the responsibility of the person who designs the pneumatic system or decides its specifications.

Since the products specified here are used in various operating conditions, their compatibility with the specific pneumatic system must be based on specifications, or post analysis, and / or tests to meet your specific requirements.

2.Only trained personnel should operate pneumatically operated machinery and equipment. Compressed air can be dangerous if an operator is unfamiliar with it.

Assembly, handling or repair of pneumatic systems should be performed by trained and experienced operators.

3.Do not service machinery / equipment or attempt to remove components until safety is confirmed. 1.Inspection and maintenance of machinery / equipment should only be performed after confirmation of safe locked-out control positions.

2.When equipment is to be removed, confirm the safety process as mentioned above.

Cut the supply pressure for the equipment and exhaust all residual compressed air in the system.

3.Before machinery / equipment is re-started, take measures to prevent quick extensions of the cylinder piston rod etc. ( Bleed air into the system gradually to create back-pressure. )

4.Contact SMC if the product is to be used in any of the following conditions:

1.Conditions and environments beyond the given specifications, or if product is used outdoors.

2.Installation on equipment in conjunction with atomic energy, railway, air navigation, vehicles, medical equipment, food and beverage, recreation equipment, emergency stop circuits, press applications, or safety equipment.

3.An application which has the possibility of having negative effects on people, property, or animals, requires special safety analysis.

・Safety instructions for electric equipment

！WARNING

1.The product specified here is designed to be used in ordinary factory automation equipment.

Prevent the use in machinery and / or equipment where human life may be directly injured and malfunction or failure may cause enormous loss.

2.Do not use in the explosive atmosphere, the atmosphere of flammable gas, the corrosive atmosphere. In these atmospheres, it may cause injury or fire.

3.Only The person who has professional knowledge should implement work of the carriage, the establishment, the piping, the wiring, the operation, the handling, the maintenance, the check.

If not, it will cause in being shocked, the injury, the fire and so on.

4.Install a direct stop circuit outside that to stop operation immediately and then to shut the power supply.

5.Do not disassemble the product for modifications.

It may injure the person or damage the property.

6.Do not wipe this product with any chemical solvent.

-1 -

Page 1 Page 3
Image 2
Page 1 Page 3
Contents SMC Corporation ・Level of potential hazard ・Safety instructions for pneumatic equipment・Safety instructions for electric equipment ・Safety instructions for cables ！ Caution・Safety instructions for power supply Index EX500 Serial System System Structure Outline Gateway GW UnitInput / Output Unit ・EMC Directive 89 / 336 / EEC SpecificationTest Procedure Specification Criterion Electromagnetic EmissionGateway GW Unit specification How to Order 5 0 0 G D NDeviceNet communication specification EX500 GDN1 PROFIBUS-DP communication specification EX500 GPR1 PROFIBUS-DP EN501701. Input Manifold Input Unit specificationInput Unit Manifold 2. Input Unit3. Input Block Input Block specificationHow to Order 5 0 0 I E Applicable Manifold Valve series SI Unit specificationSI Unit SI Unit for SV series Manifold ValveCable specification Electric specificationCommunication Connector Cable for DeviceNet EX500 GDN1 Option2. Branch Cable with M12 Connector How to Order 5 0 0 a C 0 3 0 S S P S5. Water Proof Cap 3. Power Supply Connector Cable4. Terminal Plug Parts description ・Representative PLCLED display Operation settingDisplay Content Setting Operation 1. Operation setting switch SW12. Operation setting switch SW2 Data Rate 3. Terminating resistance setting switch SW3Layout of scanner I/O State of SW3・Cable specification How to operate EX500 GDN1 DeviceNet Connection style・Wiring length EDO Figure of setting switch I/O memory map 1. Address setting switch SW12. Data rate setting switch SW3 ・Terminating resistance How to operate EX500 GPR1 PROFIBUS-DP Communication wiring・Communication speed and Longest wiring length DIA ・In case of corresponding with Word 1. Address setting switch SW1, 22. Terminating resistance setting switch SW4 State of SW4・In case of corresponding with Double Word Correspondence of input number and Input Block Power supply must be reset after fixing the short circuitInput Unit Manifold Parts description Input Unit・Addition of the Input Block ・Parts list Parts name Parts numberExploded view / Input Unit Manifold VQC series Manifold Valve Parts descriptionSV series SI Unit for SV series ManifoldCorrespondence of output number and Manifold Valve SI Unit for VQC series Manifold How to install the SI UnitSI Unit for SV series Manifold Individual power supply WiringSource wiring Single power supplyRemote I/O EX500 GAB1 -X1 communication wiring Communication wiring 1. Communication wiring to PLC2. Communication wiring to the SI Unit and the Input Unit DeviceNet EX500 GDN1 communication wiringStations Dimension 10 -1. Gateway GW Unit 10 -2. Input Unit Manifold・In case of M8 Input Block 10 -3. Manifold Valve ・In case of M12 Input Block・Remote I/O communication Remedies Trouble shooting・Whole system Remedies Status of MS LED ・DeviceNet communication Remedies・PROFIBUS-DP communication Remedies Status of NS LED
Top Page Image Contents