SMC Networks EX500 manual Figure of setting switch

Page 24

EX500 Serial System

EX## - OME0008

5 -3. LED display

BUS

MS

NS

SOL

GATEWAY UNIT EX500 SERIES

		COM A	COM B	COM C	COM D

	Display			Content

	MS	Operating in a normal condition				: Green lights
	MS	Recoverable fault ( Memory is abnormal )				: Red lights
		Recoverable fault ( Memory is abnormal )				: Red lights
		Not online				: Lights off
		Online , Not Allocated				: Green flashing
	NS	Online , Allocated				: Green lights
		Connection Time - Out				: Red flashing
		Critical Link Failure				: Red lights
	SOL	Solenoid valve source voltage is normal				: Lights
	SOL	Voltage lowered to 20V or less				: Lights off
		Voltage lowered to 20V or less				: Lights off
	COM A	Communication port A is receiving data				: Lights
	COM A	Communication port A has no data				: Lights off
		Communication port A has no data				: Lights off
	COM B	Communication port B is receiving data				: Lights
	COM B	Communication port B has no data				: Lights off
		Communication port B has no data				: Lights off
	COM C	Communication port C is receiving data				: Lights
	COM C	Communication port C has no data				: Lights off
		Communication port C has no data				: Lights off
	COM D	Communication port D is receiving data				: Lights
	COM D	Communication port D has no data				: Lights off
		Communication port D has no data				: Lights off

！ CAUTION

When the Input Unit Manifold is not connected, the respective COM LED of the GW Unit will not light up. To monitor the status of COM port, it is necessary to use a Terminal Plug.

The COM LED will light up when a Terminal Plug is used. ( Refer to section 3 -6 -4 )

5 -4. Operation setting

Turn the power supply OFF when setting switches.

Open the station switch protection cover and set the rotary switch with a flat blade screw driver.

SW1 SW2 SW3

0

9 1

82

7

3

64

5

Figure of setting switch

- 23 -

Image 24

Contents SMC Corporation ・Safety instructions for pneumatic equipment ・Safety instructions for electric equipment・Level of potential hazard ・Safety instructions for cables ！ Caution・Safety instructions for power supply Index EX500 Serial System Outline Gateway GW Unit Input / Output UnitSystem Structure Specification Test Procedure Specification Criterion・EMC Directive 89 / 336 / EEC Electromagnetic EmissionGateway GW Unit specification How to Order 5 0 0 G D NDeviceNet communication specification EX500 GDN1 PROFIBUS-DP communication specification EX500 GPR1 PROFIBUS-DP EN50170Input Unit specification Input Unit Manifold1. Input Manifold 2. Input UnitInput Block specification How to Order 5 0 0 I E3. Input Block SI Unit specification SI UnitApplicable Manifold Valve series SI Unit for SV series Manifold ValveElectric specification Communication Connector Cable for DeviceNet EX500 GDN1Cable specification Option2. Branch Cable with M12 Connector How to Order 5 0 0 a C 0 3 0 S S P S3. Power Supply Connector Cable 4. Terminal Plug5. Water Proof Cap Parts description ・Representative PLCOperation setting Display ContentLED display 1. Operation setting switch SW1 2. Operation setting switch SW2Setting Operation 3. Terminating resistance setting switch SW3 Layout of scanner I/OData Rate State of SW3How to operate EX500 GDN1 DeviceNet Connection style ・Wiring length・Cable specification EDO Figure of setting switch 1. Address setting switch SW1 2. Data rate setting switch SW3I/O memory map How to operate EX500 GPR1 PROFIBUS-DP Communication wiring ・Communication speed and Longest wiring length・Terminating resistance DIA 1. Address setting switch SW1, 2 2. Terminating resistance setting switch SW4・In case of corresponding with Word State of SW4・In case of corresponding with Double Word Power supply must be reset after fixing the short circuit Input Unit Manifold Parts descriptionCorrespondence of input number and Input Block Input Unit・Parts list Parts name Parts number Exploded view / Input Unit Manifold・Addition of the Input Block Manifold Valve Parts description SV seriesVQC series SI Unit for SV series ManifoldCorrespondence of output number and Manifold Valve How to install the SI Unit SI Unit for SV series ManifoldSI Unit for VQC series Manifold Wiring Source wiringIndividual power supply Single power supplyCommunication wiring 1. Communication wiring to PLC 2. Communication wiring to the SI Unit and the Input UnitRemote I/O EX500 GAB1 -X1 communication wiring DeviceNet EX500 GDN1 communication wiringDimension 10 -1. Gateway GW Unit 10 -2. Input Unit Manifold ・In case of M8 Input BlockStations 10 -3. Manifold Valve ・In case of M12 Input BlockTrouble shooting ・Whole system Remedies・Remote I/O communication Remedies ・DeviceNet communication Remedies ・PROFIBUS-DP communication RemediesStatus of MS LED Status of NS LED