On-Q/Legrand 364732-01 What is PPPoE PPP over Ethernet ?, How can I know if I am using PPPoE?

Page 33

6.What is PPPoE (PPP over Ethernet )?

PPPoE is also known as a dial-up DSL service. It is designed to integrate broadband services into the current widely deployed, easy-to-use, and low-cost dial-up-access networking infrastructure. Thus, a customer can get greater access speed without changing the familiar dial operation concept.

7.How can I know if I am using PPPoE?

PPPoE client software is provided by the ISP and should be installed onto your computer first. You run the program to connect to/disconnect from the Internet. User Account information (User Name and Password) is also required each time you connect to the Internet access.

Note: After you have entered the PPPoE information during the device setup, and started up the device, the device will provide your ISP with the PPPoE information and login automatically.

8.What does the message “IP address conflict” mean?

When you see the message box prompt for IP address conflict on any of the workstations in the network, this means two or more workstations have the same IP address. If you have setup the device as a DHCP server, run IPCONFIG /release and then run IPCONFIG /renew on the problem workstation (for Windows 98SE or ME, run the "winipcfg" utility, select the correct Network Adapter, click “release all” to release all current configuration, then click “renew all” to renew the IP information again,). If the DHCP function is disabled and static IP addresses are assigned to each workstation, please double check each workstation’s IP address for any duplicate IP addresses.

9.What does “Can not access the Internet” mean?

Check the physical connectivity of the local network and broadband device.

Make sure you are using the correct cables and the cables are connected to the network devices properly. Examine the LED of LAN port and the LED of the broadband signal input on the Cable Modem/xDSL Modem. If the LAN LED is off, make sure you are using the correct cables and the cables are connected to the devices properly. If the LED of the broadband signal is off, please contact your ISP.

Check the status of this product.

After checking the cabling and LEDs, you also have to check if you have entered the correct user name and password that your ISP provided. While checking, please note that the information is case

sensitive. To check the Internet connection status, open the browser to start the Web configuration, select Network Status ÆWAN IP Status. Check if Link Status displays “Connect successfully”. If not, you may have to contact your ISP to see if their Internet service is available.

Check the logical connectivity from your computer to the Internet (TCP/IP Network Diagnosis). The WINIPCFG program (for Win95, 98, and ME) or IPCONFIG program (for Windows 2000, NT, XP) is used to gather information about the TCP/IP connections that are active on your system. It cannot be used to dynamically adjust TCP/IP connections, but can be used to get the current IP address assignments.

For Win 95/98/ME, from Windows, go to Start, click Run, enter WINIPCFG, and click OK.

Figure 26

Innovations in Home Living.

301 Fulling Mill Road, Suite G ©Copyright 2004 by OnQ Technologies, Inc All Rights Reserved.

Middletown, PA 17057

www.onqhome.com

(800)-321-2343

30

Page 32 Page 34
Image 33
Page 32 Page 34
Contents
Port ROUTER/SWITCH P/N CE Mark Warning FCC CertificationsTable of Contents Introduction Small Office/ Home Office SetupII. Product Overview Router/Switch 9VDC Power Supply P/NRouter/Switch Module Connection Area Switch Port LEDs WAN LED Status LEDVDC Input Network Port Local Switch Ports III. Installation Innovations in Home Living Not run PPPoE software on your computers Obtain configuration automaticallyDevice Information Adapter Address Static configuration is selectedUnless you are sure it is necessary to modify your MAC Address. To modify the addressAddress PPPoE DSL dynamic ModeCheck Modify and enter the desired MAC Input for this field is 32 alphanumeric charactersClick on Help connecting to certain web sites or speedingDevice will save Information, restart and return to the previousNot alter the content unless you are sure it is Static ModeNecessary to modify your MAC address. To modify You with the nameSave Undo Following field for you to enter the starting IP Check this radio button to enable this device toAddresses. Click Back to return to the Local Port To continueWins server Advanced Setup Modify the Configuration PortChange Administrator’s password Address with all F’s EnableBlock Internet ResultVirtual Server Undo ADD IP Range IP addressesIP addresses to filter/forward Direction ~From Local IP ~To Remote IPFilter List Displays all the Packet Filters Added filter will appear on the Filter ListClick to delete all the filters on the list Click on the Index drop-down menu to selectStatic Route To save the settings After completing the settings on this page, clickTo clear all the settings on this SaveUndo Save RELEASE/DISCONNECT Network Status Connection StatusInformation on the Internet Port RENEW/CONNECTRefresh Click this button to refresh the list To reset to factory default settings, click the GO button Others Factory Reset see FigureTo save the current configuration to file Save ConfigurationSettings Load Configuration From File File Path/NameUpgrade NOW Firmware Upgrade see FigureWhat is a DMZ? VI. TroubleshootingHow can I know if I am using PPPoE? What is PPPoE PPP over Ethernet ?What does the message IP address conflict mean? Check the status of this productIP Configuration Reply from 192.168.0.1 bytes=32 time=3ms TTL=100 Type ping 168.95.192.1 and click OKWAN NTP, HTTP, TftpAOE 2300-2400tcp 2300-2400udp 47624tcp VDO Live NoneAuthentication Chap Is now available Connecting to serverPassword AuthenticationCHAP failure Xxx Minutes Connection establish timeout
Top Page Image Contents