On-Q/Legrand 364732-01 Save Configuration, To save the current configuration to file, Settings

Page 30

2.Save Configuration

This function (see Figure 22) enables users to always save the current configurations as a file (i.e. config.sav), so that no re-entry is required when users want to switch between various configurations. To load a configuration from a file, enter the file name or click Browse… to find the file from your computer.

Figure 22

 

 

 

 

 

Figure 23

Figure 24

 

 

 

 

 

 

SAVE

 

Click

SAVE

to save the current configuration to file.

UNDO

 

Click to clear the input.

 

LOAD

 

 

Click to start loading configuration from file when you are done with the previous

 

 

 

settings.

 

 

 

 

 

 

 

 

When prompted (see Figure 23), select “Save this file to disk”, and the Save As screen (see Figure 24) will prompt you with a dialog box to enter the file name and the file location. Please note that the configuration file is in a .sav format.

Load Configuration From File

File Path/Name

If you want to load a configuration file, enter the file name with the correct path and then click on LOAD. Or click Browse… to select the file.

Innovations in Home Living.

301 Fulling Mill Road, Suite G ©Copyright 2004 by OnQ Technologies, Inc All Rights Reserved.

Middletown, PA 17057

www.onqhome.com

(800)-321-2343

27

Page 29 Page 31
Image 30
Page 29 Page 31
Contents
Port ROUTER/SWITCH P/N FCC Certifications CE Mark WarningTable of Contents Small Office/ Home Office Setup IntroductionRouter/Switch 9VDC Power Supply P/N II. Product OverviewRouter/Switch Module Connection Area Switch Port LEDs WAN LED Status LEDVDC Input Network Port Local Switch Ports III. Installation Innovations in Home Living Obtain configuration automatically Not run PPPoE software on your computersUnless you are sure it is necessary to modify your MAC Static configuration is selectedDevice Information Adapter Address Address. To modify the addressCheck Modify and enter the desired MAC PPPoE DSL dynamic ModeAddress Input for this field is 32 alphanumeric charactersDevice will save Help connecting to certain web sites or speedingClick on Information, restart and return to the previousNecessary to modify your MAC address. To modify Static ModeNot alter the content unless you are sure it is You with the nameSave Undo Check this radio button to enable this device to Following field for you to enter the starting IPAddresses. Click Back to return to the Local Port To continueWins server Advanced Setup Modify the Configuration PortChange Administrator’s password Block Internet EnableAddress with all F’s ResultVirtual Server Undo ADD IP addresses to filter/forward IP addressesIP Range Direction ~From Local IP ~To Remote IPClick to delete all the filters on the list Added filter will appear on the Filter ListFilter List Displays all the Packet Filters Click on the Index drop-down menu to selectStatic Route To clear all the settings on this After completing the settings on this page, clickTo save the settings SaveUndo Save Information on the Internet Port Network Status Connection Status RELEASE/DISCONNECT RENEW/CONNECTRefresh Click this button to refresh the list Others Factory Reset see Figure To reset to factory default settings, click the GO buttonSettings Save ConfigurationTo save the current configuration to file Load Configuration From File File Path/NameFirmware Upgrade see Figure Upgrade NOWVI. Troubleshooting What is a DMZ?What does the message IP address conflict mean? What is PPPoE PPP over Ethernet ?How can I know if I am using PPPoE? Check the status of this productIP Configuration Type ping 168.95.192.1 and click OK Reply from 192.168.0.1 bytes=32 time=3ms TTL=100AOE NTP, HTTP, TftpWAN 2300-2400tcp 2300-2400udp 47624tcp VDO Live NonePassword AuthenticationCHAP failure Is now available Connecting to serverAuthentication Chap Xxx Minutes Connection establish timeout
Top Page Image Contents