On-Q/Legrand 364732-01 owner manual Type ping 168.95.192.1 and click OK

Page 35

If the product is working properly, the following should be apparent from this screen:

1)The Client should have an IP address within the prescribed range (default 192.168.1. #; where # is from 1 ~ 253).

2)The “DHCP” and “Default Gateway” should list the product’s local port address (the device’s IP address; default 192.168.1.254).

3)The DNS server IP addresses should match the DNS server IP addresses set in the device.

For Win NT and Win2000, go to “Start”Æ”Programs”Æ”Accessories”Æ”Command Prompt” to open the Command Prompt. Type in IPCONFIG /ALL and hit “Enter” to see the adapter’s information. Type in IPCONFIG /RELEASE to release all adapters’ IP address and IPCONFIG /RENEW to renew IP addresses. For a list of the IPCONFIG commands, type in IPCONFIG /?.

The PING.EXE command is used to verify that a computer is active and available. Users can ping a specific destination domain name or just the IP address.

For example, to find the server 168.95.192.1, type the following command at the MS-DOS prompt and then press “Enter”:

C:\>ping 168.95.192.1

PING can be executed in Windows as shown below:

1.Go to the Start menu.

2.Click Run.

3.Type ping 168.95.192.1 and click OK.

4.The server (IP address) is online if the following message appears.

Reply from 192.168.0.1: bytes=32 time=3ms TTL=100

5.The destination device is not reachable if the following message appears.

Reply from 192.168.0.1: Destination host unreachable or Request timed out.

To insure you are communicating with the ISP, Issue a PING command to the IP address of your ISP’s Gateway or DNS server.

For example, if the DNS server address is 203.66.81.254, at C:\> prompt, enter Ping 203.66.81.254. If successful, you can reach your ISP server.

If unsuccessful (Request timeout), you may have trouble connecting to your ISP, please verify that the product is properly configured to connect to your ISP. Also verify that your Cable/DSL modem and the line are functioning.

To insure you have access to the Internet, PING an IP address or domain name on Internet.

For example, at the command prompt enter C:\> PING 168.95.192.1 –w 5000 or

C:\> PING www.yahoo.com –w 5000

If successful, you are connected to the Internet.

If you can ping the ISP’s gateway, but cannot ping a specific site (e.g. www.yahoo.com) on the Internet, chances are, your ISP has an internal problem (DNS server not available).

Innovations in Home Living.

301 Fulling Mill Road, Suite G ©Copyright 2004 by OnQ Technologies, Inc All Rights Reserved.

Middletown, PA 17057

www.onqhome.com

(800)-321-2343

32

Page 34 Page 36
Image 35
Page 34 Page 36
Contents
Port ROUTER/SWITCH P/N CE Mark Warning FCC CertificationsTable of Contents Introduction Small Office/ Home Office SetupII. Product Overview Router/Switch 9VDC Power Supply P/NVDC Input Network Port Local Switch Ports Router/Switch Module Connection AreaSwitch Port LEDs WAN LED Status LED III. Installation Innovations in Home Living Not run PPPoE software on your computers Obtain configuration automaticallyAddress. To modify the address Static configuration is selectedDevice Information Adapter Address Unless you are sure it is necessary to modify your MACInput for this field is 32 alphanumeric characters PPPoE DSL dynamic ModeAddress Check Modify and enter the desired MACInformation, restart and return to the previous Help connecting to certain web sites or speedingClick on Device will saveYou with the name Static ModeNot alter the content unless you are sure it is Necessary to modify your MAC address. To modifySave Undo Following field for you to enter the starting IP Check this radio button to enable this device toWins server Addresses. Click Back to return to the Local PortTo continue Change Administrator’s password Advanced SetupModify the Configuration Port Result EnableAddress with all F’s Block InternetVirtual Server Undo ADD Direction ~From Local IP ~To Remote IP IP addressesIP Range IP addresses to filter/forwardClick on the Index drop-down menu to select Added filter will appear on the Filter ListFilter List Displays all the Packet Filters Click to delete all the filters on the listStatic Route Save After completing the settings on this page, clickTo save the settings To clear all the settings on thisUndo Save RENEW/CONNECT Network Status Connection StatusRELEASE/DISCONNECT Information on the Internet PortRefresh Click this button to refresh the list To reset to factory default settings, click the GO button Others Factory Reset see FigureLoad Configuration From File File Path/Name Save ConfigurationTo save the current configuration to file Settings Upgrade NOW Firmware Upgrade see FigureWhat is a DMZ? VI. TroubleshootingCheck the status of this product What is PPPoE PPP over Ethernet ?How can I know if I am using PPPoE? What does the message IP address conflict mean?IP Configuration Reply from 192.168.0.1 bytes=32 time=3ms TTL=100 Type ping 168.95.192.1 and click OK2300-2400tcp 2300-2400udp 47624tcp VDO Live None NTP, HTTP, TftpWAN AOEXxx Minutes Connection establish timeout Is now available Connecting to serverAuthentication Chap Password AuthenticationCHAP failure
Top Page Image Contents