On-Q/Legrand 364732-01 Device’s Internet Port is not connected to the ISP’s, Server found, Failed

Page 37

Appendix C INTERNET PORT LINK STATUS

PPPoE link status

“PPPoE offline. Ready to connect.”

Device’s Internet Port is not connected to the ISP’s

 

dialup server. Dialup server for connecting to the Internet

 

is now available.

 

"Connecting to server."

Device's Internet Port is now dialing to dialup server.

"Server found."

Device dialed to dialup server, and is negotiating with

 

dialup server.

 

"Start PPP negotiation."

Negotiation is ongoing.

 

"Authentication (PAP)."

Server is verifying the dialup account with PAP method.

"Authentication (CHAP)."

Server is verifying the dialup account with CHAP method.

"Obtaining WAN IP address."

Authentication is successful! Device now is obtaining IP

 

address from the dialup server.

 

"Connect successfully."

Device dials up to server successfully. User can connect

 

to internet now.

 

"Can not find server."

Device cannot dial up to the dialup server. Dial-up to

 

server failed.

 

"Fail on LCP stage."

Configuration for network link failed.

 

"Authentication(PAP) failure."

Failed in authentication; failure was caused by wrong

 

password.

 

"Authentication(CHAP) failure."

Verification on the identity of the device dialup account

 

failed.

 

"Fail to Obtain Internet IP address."

Device cannot obtain IP address from the dialup server.

 

Dial-up to server failed.

 

"Server dropped the connection."

Server cut the device's internet

connection.

 

Device is disconnected to the Internet.

 

"Disconnect on idle."

Device has been idle longer than the idle interval and

 

was cut off from the connection.

The idle

 

interval value was set in the field "Auto-disconnect if idle

 

xxx Minutes".

 

"Connection establish timeout."

Device was re-trying to dialing-up to server and failed.

 

Device finally gave up dialing to the server.

 

DHCP link status

 

 

 

 

"DHCP already claimed"

Device obtained IP address from DHCP server.

"DHCP under claiming"

Device is trying to obtain IP address from DHCP server.

Static IP assignment link status

“Static assigned”

IP address succeeds in manually setting up.

Innovations in Home Living.

301 Fulling Mill Road, Suite G ©Copyright 2004 by OnQ Technologies, Inc All Rights Reserved.

Middletown, PA 17057

www.onqhome.com

(800)-321-2343

34

Page 36 Page 37
Image 37
Page 36 Page 37
Contents
Port ROUTER/SWITCH P/N CE Mark Warning FCC CertificationsTable of Contents Introduction Small Office/ Home Office SetupII. Product Overview Router/Switch 9VDC Power Supply P/NSwitch Port LEDs WAN LED Status LED Router/Switch Module Connection AreaVDC Input Network Port Local Switch Ports III. Installation Innovations in Home Living Not run PPPoE software on your computers Obtain configuration automaticallyDevice Information Adapter Address Static configuration is selectedUnless you are sure it is necessary to modify your MAC Address. To modify the addressAddress PPPoE DSL dynamic ModeCheck Modify and enter the desired MAC Input for this field is 32 alphanumeric charactersClick on Help connecting to certain web sites or speedingDevice will save Information, restart and return to the previousNot alter the content unless you are sure it is Static ModeNecessary to modify your MAC address. To modify You with the nameSave Undo Following field for you to enter the starting IP Check this radio button to enable this device toTo continue Addresses. Click Back to return to the Local PortWins server Modify the Configuration Port Advanced SetupChange Administrator’s password Address with all F’s EnableBlock Internet ResultVirtual Server Undo ADD IP Range IP addressesIP addresses to filter/forward Direction ~From Local IP ~To Remote IPFilter List Displays all the Packet Filters Added filter will appear on the Filter ListClick to delete all the filters on the list Click on the Index drop-down menu to selectStatic Route To save the settings After completing the settings on this page, clickTo clear all the settings on this SaveUndo Save RELEASE/DISCONNECT Network Status Connection StatusInformation on the Internet Port RENEW/CONNECTRefresh Click this button to refresh the list To reset to factory default settings, click the GO button Others Factory Reset see FigureTo save the current configuration to file Save ConfigurationSettings Load Configuration From File File Path/NameUpgrade NOW Firmware Upgrade see FigureWhat is a DMZ? VI. Troubleshooting How can I know if I am using PPPoE? What is PPPoE PPP over Ethernet ? What does the message IP address conflict mean? Check the status of this productIP Configuration Reply from 192.168.0.1 bytes=32 time=3ms TTL=100 Type ping 168.95.192.1 and click OKWAN NTP, HTTP, TftpAOE 2300-2400tcp 2300-2400udp 47624tcp VDO Live NoneAuthentication Chap Is now available Connecting to serverPassword AuthenticationCHAP failure Xxx Minutes Connection establish timeout
Top Page Image Contents