Multi-Tech Systems MT3334ZDXV owner manual S48, S89

Page 40

MT3334ZDX/V Owner's Manual

Register:	S48
Unit:	decimal
Range:	7 or 128
Default:	7
Description:	The following chart lists the S36 and S48
	configuration settings necessary to negotiate
	certain types of connections.

Register:	S89
Unit:	seconds
Range:	0, 5-255
Default:	10
Description:	Sets the length of time in the off-line command
	mode before the modem goes into standby mode.
	A value of zero prevents standby mode; a value of
	1–4 sets the value to 5.

40

Image 40

Contents Page Patents Revision DescriptionContents Index Introduction and Description Requirements ComputerSerial Cable Telephone LineCommunications Software Product FeaturesData Installation and Connection About this ManualFax Voice Model MT3334ZDXV onlyAT Commands, S-Registers and Result Codes Testing Your ModemService, Warranty & Technical Support AppendicesSafety Warnings Installation IntroductionInstallation Process Page MultiModemZDX Connections LED Indicators Front PanelInstallation Is Your MultiModemZDX Ready for Use? Operating Your MultiModemZDX Simple OperationsRemote Configuration Software Configuration AT&FcrMultiModemZDX Configuration Confirmation Hardware/Software ConfirmationTroubleshooting None of the LEDs Light When the Modem Is OnModem Does Not Respond to Commands Installation Modem Dials But Cannot Make Connection Installation Modem Cannot Connect When Answering Modem Disconnects While OnlineSlow File Transfer Losing DataGarbage Characters on the Monitor AT Commands, S-Registers Result Codes Command Summary Dial Echo Command Mode CharactersDial string modifiers Monitor Speaker Volume Monitor Speaker ModeEcho Online Data Characters On-Hook/Off-Hook ControlReturn Online to Data Mode Enable/Disable Result CodesModulation Handshake = n Set Register ValueModem Reset Result Code SelectionLong Space Disconnect Data Carrier Detect DCD ControlLoad Factory Default Settings Communications ModeData Terminal Ready DTR Control 22bis Guard Tone ControlATDS=n \N n Error Correction Mode Selection \K n Set Break Control\V n Protocol Result Code Data Compression ControlModem Baud Rate Serial Port Baud RateRegisters Register Unit Seconds Range 255 Default Description S10S11 S28S30 S35S42 S37S43 S48 S89Delayed Terse Verbose DescriptionModem Testing Local Analog Loopback Test/V.54 Loop Local Analog Loopback TestDigital Loopback Test/V.54 Loop 2 Local/Manual Digital Loopback Test/V.54 Loop 2 Remote/Auto Digital Loopback Testlocal/manualDigital Loopback Test remote/automatic Limited Warranty Tech Support On-line Warranty RegistrationRecording Modem Information Service About the Multi-Tech BBS No Longer Available Logging on to the Multi-Tech BBSDownloading a File If you know the file nameLeaving a Message Reading a MessageIf you don’t know the file name About CompuServe/Internet No Longer Available Multi-Tech Fax-Back Service No Longer AvailableBulletins Appendix a Technical Specifications Intelligent Features Command BufferData Modulation Fax Modulation2400 & 1200 bps 22bis/V.22Carrier Frequencies Fax 21 CH2 Half DuplexConnectors DiagnosticsIndicators Temperature Power Requirement697 770 852 941 Appendix B Tone Dial FrequenciesAppendices MT3334ZDX, MT3334ZDXV Appendices Canadian Limitations Notice Compliance with Babt Requirements European Low Voltage DirectivePage Compliance with BS6789 .1 and Part Compliance with BS6328 PartModem CE Mark EMC and Safety Compliance Modem Commands Default Permissible RangeRegister Default Permissible Range Australian and New Zealand Modem Warning NoticeNew Zealand Telecom Warning Notice Call Attempts/RetriesIndex Error Correction Page MT5634ZDXv Connections Power Supply Index