Multi-Tech Systems MT3334ZDX Compliance with Babt Requirements, European Low Voltage Directive

Page 61

Appendices

Compliance with BABT Requirements

Approved for connection to telecommunications system specified in the instructions for use subject to the conditions set out in them.

Warning: Interconnection directly, or by way of other apparatus, of ports marked "SAFETY WARNING see instructions for use" with ports marked or not so marked may produce hazardous conditions on the network. Advice should be obtained from a competent engineer before such a connection is made.

This apparatus has been approved for the use of the following facilities:

Auto-calling

Loop disconnect and MF dialing

Phone number storage and retrieval by a predetermined code

Operation in the absence of proceed indication

Automatic storage of last number dialed

Tone detection-busy

Auto clear from the originating end

DTR dialing

Modem

PBX timed break register recall

European Low Voltage Directive

When correctly installed and maintained, the modem will present no hazard to the user. When correctly installed the modem will be connected to the PSTN or a PW and to a Data Terminal Equipment (DTE), whose modem connections comply with ITU recommendation V28. The DTE connections are therefore taken to be safe voltages (less than ± 30 volts).

The main power source shall be installed near to the equipment and shall be easily accessible. The plug that connect to the apparatus to the main power supply must be fitted with a 5A fuse that complies with BSI1362.

Ports which are capable of connecting to other apparatus are defined as SELV. To ensure conformity with EN41003, ensure that these ports are only connected to ports of the same type on other apparatus.

61

Image 61
Contents Page Revision Description PatentsContents Index Computer Introduction and Description RequirementsSerial Cable Telephone LineCommunications Software Product FeaturesData About this Manual Installation and ConnectionFax Voice Model MT3334ZDXV onlyTesting Your Modem AT Commands, S-Registers and Result CodesService, Warranty & Technical Support AppendicesSafety Warnings Installation IntroductionInstallation Process Page MultiModemZDX Connections Front Panel LED IndicatorsInstallation Is Your MultiModemZDX Ready for Use? Simple Operations Operating Your MultiModemZDXRemote Configuration AT&Fcr Software ConfigurationHardware/Software Confirmation MultiModemZDX Configuration ConfirmationNone of the LEDs Light When the Modem Is On TroubleshootingModem Does Not Respond to Commands Installation Modem Dials But Cannot Make Connection Installation Modem Disconnects While Online Modem Cannot Connect When AnsweringLosing Data Slow File TransferGarbage Characters on the Monitor AT Commands, S-Registers Result Codes Command Summary Dial Echo Command Mode CharactersDial string modifiers Monitor Speaker Mode Monitor Speaker VolumeEcho Online Data Characters On-Hook/Off-Hook ControlEnable/Disable Result Codes Return Online to Data ModeModulation Handshake = n Set Register ValueResult Code Selection Modem ResetLong Space Disconnect Data Carrier Detect DCD ControlCommunications Mode Load Factory Default SettingsData Terminal Ready DTR Control 22bis Guard Tone ControlATDS=n \K n Set Break Control \N n Error Correction Mode Selection\V n Protocol Result Code Data Compression ControlSerial Port Baud Rate Modem Baud RateRegisters S10 Register Unit Seconds Range 255 Default DescriptionS28 S11S30 S35S42 S37S43 S89 S48Terse Verbose Description DelayedLocal Analog Loopback Test Modem Testing Local Analog Loopback Test/V.54 LoopDigital Loopback Test/V.54 Loop 2 Local/Manual Digital Loopback Testlocal/manual Digital Loopback Test/V.54 Loop 2 Remote/AutoDigital Loopback Test remote/automatic Limited Warranty Tech Support On-line Warranty RegistrationRecording Modem Information Service Logging on to the Multi-Tech BBS About the Multi-Tech BBS No Longer AvailableDownloading a File If you know the file nameLeaving a Message Reading a MessageIf you don’t know the file name About CompuServe/Internet No Longer Available Multi-Tech Fax-Back Service No Longer AvailableBulletins Appendix a Technical Specifications Command Buffer Intelligent FeaturesData Modulation Fax Modulation22bis/V.22 2400 & 1200 bpsCarrier Frequencies Fax 21 CH2 Half DuplexDiagnostics ConnectorsIndicators Temperature Power RequirementAppendix B Tone Dial Frequencies 697 770 852 941Appendices MT3334ZDX, MT3334ZDXV Appendices Canadian Limitations Notice European Low Voltage Directive Compliance with Babt RequirementsPage Compliance with BS6328 Part Compliance with BS6789 .1 and PartModem Commands Default Permissible Range Modem CE Mark EMC and Safety ComplianceRegister Default Permissible Range Australian and New Zealand Modem Warning NoticeCall Attempts/Retries New Zealand Telecom Warning NoticeIndex Error Correction Page MT5634ZDXv Connections Power Supply Index