Multi-Tech Systems MT3334ZDXV owner manual Power Supply

Page 70

MT3334ZDX/V Owner's Manual
P
Pause, Dialing	37
Power Requirements	55
Power Supply	10, 19
Protocol Result Code	34
Protocols	25
R
Read Register Value	30
Reading a Message	50
Receive Data	12
Receiver Sensitivity	54
Repeat Last Command	27
Result Code Selection	31
Result Codes	22
Return Character (S3)	36
Return Online to Data Mode	30
Ringer Equivalence Number	62
RS-232	5
S
Select Stored Configuration for Hard Reset	33
Serial Cable	20
Serial Port	21, 25
Set Break Control	34
Set Register Value	30
Software User License Agreement	47
Speaker	55
Speakerphone	7
Speed Conversion	52
Speed, transmission
Data	6
Fax	7
Store Current Configuration	33
Store Telephone Number	33

70

Image 70

Contents Page Patents Revision DescriptionContents Index Serial Cable Introduction and Description RequirementsComputer Telephone LineCommunications Software Product FeaturesData Fax Installation and ConnectionAbout this Manual Voice Model MT3334ZDXV onlyService, Warranty & Technical Support AT Commands, S-Registers and Result CodesTesting Your Modem AppendicesSafety Warnings Installation IntroductionInstallation Process Page MultiModemZDX Connections LED Indicators Front PanelInstallation Is Your MultiModemZDX Ready for Use? Operating Your MultiModemZDX Simple OperationsRemote Configuration Software Configuration AT&FcrMultiModemZDX Configuration Confirmation Hardware/Software ConfirmationTroubleshooting None of the LEDs Light When the Modem Is OnModem Does Not Respond to Commands Installation Modem Dials But Cannot Make Connection Installation Modem Cannot Connect When Answering Modem Disconnects While OnlineSlow File Transfer Losing DataGarbage Characters on the Monitor AT Commands, S-Registers Result Codes Command Summary Dial Echo Command Mode CharactersDial string modifiers Echo Online Data Characters Monitor Speaker VolumeMonitor Speaker Mode On-Hook/Off-Hook ControlModulation Handshake Return Online to Data ModeEnable/Disable Result Codes = n Set Register ValueLong Space Disconnect Modem ResetResult Code Selection Data Carrier Detect DCD ControlData Terminal Ready DTR Control Load Factory Default SettingsCommunications Mode 22bis Guard Tone ControlATDS=n \V n Protocol Result Code \N n Error Correction Mode Selection\K n Set Break Control Data Compression ControlModem Baud Rate Serial Port Baud RateRegisters Register Unit Seconds Range 255 Default Description S10S30 S11S28 S35S42 S37S43 S48 S89Delayed Terse Verbose DescriptionModem Testing Local Analog Loopback Test/V.54 Loop Local Analog Loopback TestDigital Loopback Test/V.54 Loop 2 Local/Manual Digital Loopback Test/V.54 Loop 2 Remote/Auto Digital Loopback Testlocal/manualDigital Loopback Test remote/automatic Limited Warranty Tech Support On-line Warranty RegistrationRecording Modem Information Service Downloading a File About the Multi-Tech BBS No Longer AvailableLogging on to the Multi-Tech BBS If you know the file nameLeaving a Message Reading a MessageIf you don’t know the file name About CompuServe/Internet No Longer Available Multi-Tech Fax-Back Service No Longer AvailableBulletins Appendix a Technical Specifications Data Modulation Intelligent FeaturesCommand Buffer Fax ModulationCarrier Frequencies Fax 21 CH2 2400 & 1200 bps22bis/V.22 Half DuplexIndicators ConnectorsDiagnostics Temperature Power Requirement697 770 852 941 Appendix B Tone Dial FrequenciesAppendices MT3334ZDX, MT3334ZDXV Appendices Canadian Limitations Notice Compliance with Babt Requirements European Low Voltage DirectivePage Compliance with BS6789 .1 and Part Compliance with BS6328 PartRegister Default Permissible Range Modem CE Mark EMC and Safety ComplianceModem Commands Default Permissible Range Australian and New Zealand Modem Warning NoticeNew Zealand Telecom Warning Notice Call Attempts/RetriesIndex Error Correction Page MT5634ZDXv Connections Power Supply Index