Multi-Tech Systems MT3334ZDXV Register Unit Seconds Range 255 Default Description, S10

Page 37

 

3 - AT Commands, S-Registers and Result Codes

Register:

S5

Unit:

decimal

Range:

0-32, 33-127

Default:

8(^H)

Description:

Sets ASCII code for the backspacecharacter.

 

Values greater than 32 disable the backspace

 

character.

Register:

S6

Unit:

seconds

Range:

2-65

Default:

2

Description:

Sets the time the modem waits after it goes off-

 

hook before it begins to dial the telephone number.

Register:

S7

Unit:

seconds

Range:

1-255

Default:

50

Description:

Sets the time the modem waits for a carrier signal

 

before aborting a call. Also sets the wait for silence

 

time for the @ dial modifier.

Register:

S8

Unit:

seconds

Range:

0-65

Default:

2

Description:

Sets the length of a pause caused by a comma

 

character in a dialing command.

Register:

S9

Unit:

ASCII

Range:

0-127

Default:

0

Description:

Defines Remote Configuration Escape Character.

Register:

S10

Unit:

100ms

Range:

1-254

Default:

20

Description:

Sets how long a carrier signal must be lost before

 

the modem disconnects.

37

Image 37
Contents Page Revision Description PatentsContents Index Computer Introduction and Description RequirementsSerial Cable Telephone LineCommunications Software Product FeaturesData About this Manual Installation and ConnectionFax Voice Model MT3334ZDXV onlyTesting Your Modem AT Commands, S-Registers and Result CodesService, Warranty & Technical Support AppendicesSafety Warnings Installation IntroductionInstallation Process Page MultiModemZDX Connections Front Panel LED IndicatorsInstallation Is Your MultiModemZDX Ready for Use? Simple Operations Operating Your MultiModemZDXRemote Configuration AT&Fcr Software ConfigurationHardware/Software Confirmation MultiModemZDX Configuration ConfirmationNone of the LEDs Light When the Modem Is On TroubleshootingModem Does Not Respond to Commands Installation Modem Dials But Cannot Make Connection Installation Modem Disconnects While Online Modem Cannot Connect When AnsweringLosing Data Slow File TransferGarbage Characters on the Monitor AT Commands, S-Registers Result Codes Command Summary Dial Echo Command Mode CharactersDial string modifiers Monitor Speaker Mode Monitor Speaker VolumeEcho Online Data Characters On-Hook/Off-Hook ControlEnable/Disable Result Codes Return Online to Data ModeModulation Handshake = n Set Register ValueResult Code Selection Modem ResetLong Space Disconnect Data Carrier Detect DCD ControlCommunications Mode Load Factory Default SettingsData Terminal Ready DTR Control 22bis Guard Tone ControlATDS=n \K n Set Break Control \N n Error Correction Mode Selection\V n Protocol Result Code Data Compression ControlSerial Port Baud Rate Modem Baud RateRegisters S10 Register Unit Seconds Range 255 Default DescriptionS28 S11S30 S35S42 S37S43 S89 S48Terse Verbose Description DelayedLocal Analog Loopback Test Modem Testing Local Analog Loopback Test/V.54 LoopDigital Loopback Test/V.54 Loop 2 Local/Manual Digital Loopback Testlocal/manual Digital Loopback Test/V.54 Loop 2 Remote/AutoDigital Loopback Test remote/automatic Limited Warranty Tech Support On-line Warranty RegistrationRecording Modem Information Service Logging on to the Multi-Tech BBS About the Multi-Tech BBS No Longer AvailableDownloading a File If you know the file nameLeaving a Message Reading a MessageIf you don’t know the file name About CompuServe/Internet No Longer Available Multi-Tech Fax-Back Service No Longer AvailableBulletins Appendix a Technical Specifications Command Buffer Intelligent FeaturesData Modulation Fax Modulation22bis/V.22 2400 & 1200 bpsCarrier Frequencies Fax 21 CH2 Half DuplexDiagnostics ConnectorsIndicators Temperature Power RequirementAppendix B Tone Dial Frequencies 697 770 852 941Appendices MT3334ZDX, MT3334ZDXV Appendices Canadian Limitations Notice European Low Voltage Directive Compliance with Babt RequirementsPage Compliance with BS6328 Part Compliance with BS6789 .1 and PartModem Commands Default Permissible Range Modem CE Mark EMC and Safety ComplianceRegister Default Permissible Range Australian and New Zealand Modem Warning NoticeCall Attempts/Retries New Zealand Telecom Warning NoticeIndex Error Correction Page MT5634ZDXv Connections Power Supply Index