Liebert GXT2-6000 RT208 Installing the Adjustable Rack-Mount Kit-Sold Separately, Quantity

Page 17

Installation and Configuration

6.1.2Installing the Adjustable Rack-Mount Kit—Sold Separately

This kit contains parts needed to mount several different models of UPS and external battery cabi- nets into EIA310-D standard four-post racks that are 18-32" deep (457-813mm). The weight limit per pair of adjustable rack-mounting brackets is 200 pounds (91 kg).

Parts included are:

Item

Quantity

 

 

Rear bracket members

2

 

 

Front bracket members

2

 

 

Inner bracket members

2

 

 

M4 x 8mm machine screws

16

 

 

M4 locking hex nuts

8

 

 

M5 x 16 mm machine screws

12

 

 

Grease packet.

1

 

 

Tools needed for installation are:

one Phillips screwdriver

one 7mm wrench

The adjustable rack-mounting brackets feature retaining latches to prevent users from inadvertently sliding the UPS or battery cabinet out of the rack.

To install the rack mount brackets:

1.Unpack two (2) rack-mounting bracket assemblies and mounting hardware from this kit. Bracket assemblies are interchangeable between left-hand or right-hand.

Remove inner member of each bracket assembly as shown in at right by extending it to its outermost position, depressing the retaining latch and then pulling the inner member out of the bracket assembly.

2.Determine the height position inside the rack enclosure where you want to mount the UPS or battery cabinet.

! CAUTION

Reduce the risk of tipping the rack enclosure by placing the UPS or battery cabinet in the lowest possible rack position.

Return flanges

Retaining

Latches

Front

Innermembers members

3.Install the rear member of each bracket assembly into rack enclosure with two (2) M5 screws provided in this kit (see figure at right). The return flanges on the bracket assembly fit to the inside of rack mounting rails. Insert screws loosely (finger-tight) into the top and bottom holes of the return flange on the rear member. Extend the bracket assembly by sliding the front member forward until it touches the front rack mounting rail. Insert two (2) M5 screws loosely (finger- tight) into top and bottom holes of the return flange on each front member. Make sure bracket assemblies are at the same mounting height on all four (4) rack mounting rails.

Front rack mounting rails

M5 screws

M5 screws

Rear rack mounting rails

11

Image 17
Contents GXT2-6000RT208 Power AvailabilityPage Table of Contents Controls and Indicators Configuration ProgramTroubleshooting MaintenanceSpecifications Modes of OperationFigures Important Safety Instructions Page Glossary of Symbols Introduction and System Description Battery Charger Rectifier/Power Factor Correction PFC CircuitInverter System DescriptionDynamic Bypass BatteryDC to DC Converter Major Components Internal Battery PackMain Frame and Electronics PD-001 Removable Power Distribution BoxGEC connector Mounting hardware Rack mount Handles Top bezels Tower use Battery cover grilleConfiguration Disk Ferrite Beads WHAT’S IncludedInstallation and Configuration Install the Main CabinetTower UPS Installation Attach Bezels to TopReturn flanges Retaining Latches Front Innermembers members Installing the Adjustable Rack-Mount Kit-Sold SeparatelyQuantity Rack Depth M4 nuts M4 nutsExternal Battery Cabinet Installation Replacing a power distribution box Connect Input/Output PowerDistribution Box Electrical Connections Slide cover over connec- tors Loosen screws to move coverPD-HDWR and PD-HDWR-MBS Terminal Block Connections 4 PD-001 Power Distribution BoxElectrical requirements-PD-HDWR and PD-HDWR-MBS Electrical requirements-PD-001Ground Electrode System or Protective Earth System Install the Grounding Electrode ConductorInstall the Internal Battery Pack Initial Startup and Electrical Checks Initial Startup and Electrical Checks What You Will Need GXT2-6000RT208 Configuration Program FeaturesConfiguration Program Configuration Program-Installation Establishing Communication Link with the UPS Read/Confirm UPS Configuration Settings Configuration Program-OperationChanging UPS Settings Exit Without Changing UPS SettingsOutput Voltage UPS TabAuto Restart N Reverse Detection 120V UPS Models OnlyFrequency Selection Options TabOptions Tab Used With Earlier GXT 2U Models Low Battery Time Warning Battery TabAuto Battery Test Time Battery Cabinets NumberAbout Tab Controls and Indicators ON/Alarm Silence/Battery Test ButtonOFF/Bypass Button Horizontal overlay for rack mountingFault Indicator Red Battery Level Indicators 5 GreenBypass Indicator Amber UPS on Indicator GreenBattery Mode Operation Normal Mode OperationBattery Recharge Operation Modes of OperationCommunications Communications Interface Port11.1.1 DB-9 Interface Port Communications Snmp Web Card Snmp AdapterUPS Intelligent Communications Pin 4 Remote Shutdown on BatteryRepo Connection Remote Emergency Power OffKey to Repo switch connections 1 VDC Sense Ground Maintenance Battery ReplacementInternal Battery Replacement Procedures Battery Cover Captive Screws Front BezelsConnector Connector cover Cover Electrical connectors UPS ReplacementIndicator status Diagnosis/Audible alarm TroubleshootingFault indicators Condition Alarm Alarm conditionsTroubleshooting guide Problem Cause Solution Only phase angles of 120, 180 or 240 degrees ±10 6000VA Run Time Battery run timesBattery/External Cabinets Load% Minutes Auto-Learning Battery Run Times UPS specifications SpecificationsPower distribution box specifications Battery specificationsSee Battery run times Model NumberUsed w/ UPS Model GXT2-6000RT208 Dimensions in mm Product Warranty RegistrationExternal battery cabinet specifications Specifications Page Company Behind the Products Technical Support/ServiceLocations Asia 23F, Allied Kajima Bldg