Lantronix 2100E manual Technical Specifications

Page 18

2: Introduction

LEDs

 

Meaning

 

 

 

 

 

 

Port 1 LED: Green, steady on

Idle

 

 

 

Port 1

LED: Green, blinking

Active TCP connection

 

 

 

Port 2

LED: Yellow, steady on

Idle

 

 

 

Port 2

LED: Yellow, blinking

Active TCP connection

 

 

 

Technical Specifications

 

Table 2-2. WiBox 2100E Technical Specifications

 

 

CPU, Memory

Lantronix® DSTni® EX embedded device server 186 CPU

 

256 KB zero wait state SRAM

 

2048 KB Flash

 

 

Serial Interface

Rate is software selectable (300 bps to 921600 bps)

 

 

Network Interface

Wireless 802.11b/g

 

10/100 RJ45 Ethernet (WiBox 2100E only)

 

 

Power Supply

External adapter included

 

120 VAC (1-01 models) USA

 

100 – 240 VAC (2-01 models) Universal with regional connectors

 

 

Power Input

9 – 30 VDC (2.5 W maximum)

 

DC input

 

 

Dimensions

Height: 2.3 cm (0.9 in)

 

Width: 7.3 cm (2.87 in)

 

Depth: 9.5 cm (3.74 in)

 

 

Weight

0.28 kg (0.62 lbs)

 

 

Temperature

Operating temperature range: -40°C to 70°C (-40°F to 158°F).

 

Storage temperature range: -40°C to 85°C (-40°F to 185°F)

 

 

Relative Humidity

Operating: 10% to 90% non-condensing, 40% to 60% recommended

 

Storage: 10% to 90% non-condensing

 

 

WiBox® 2100E Device Server User Guide

18

Image 18
Contents WiBox 2100E Device Server User Guide Revision History Warranty ContactsIntellectual Property Lantronix, Inc Corporate HeadquartersWiBox 2100E Device Server User Guide Table of Contents Setup Mode Server Configuration ContentsSetup Mode Advanced Settings Wireless Bridging List of Figures Chapter Summary Using This GuidePurpose and Audience Chapter DescriptionUsing This Guide Additional DocumentationDocument Description Name Model Part Numbers IntroductionApplications WiBox 2100E withApplication Examples Serial Tunneling NetworkIntroduction Ad Hoc Network Serial Tunneling InfrastructureAd Hoc WiBox 2100E Connection Configuration MethodsProtocol Support WiBox 2100E with EthernetSerial Connector Pinouts Addresses and Port NumbersDB9M DTE Serial Connector LEDs Ethernet Connector PinoutsWiBox 2100E Network Interface WiBox 2100E LEDsTechnical Specifications Installing the WiBox 2100E Getting StartedConfiguring the WiBox 2100E Getting StartedCase WEPProperty Description Installing DeviceInstaller 802.11i/WPA2-PersonalViewing the Current Configuration To view the WiBox 2100E’s configuration settingsGetting Started Web Manager Configuration Accessing Web Manager through a Web BrowserWeb Manager Configuration Network ConfigurationNetwork Mode Configuration Network ModeSelect Use the following IP configuration Automatic IP Address ConfigurationStatic IP Address Configuration Select Obtain IP address automaticallySpeed Ethernet ConfigurationAuto Negotiate DuplexServer Configuration To configure the WiBox 2100E’s device server settingsServer Configuration Hostlist Configuration AdvancedRetry Settings Channel 1 and Channel 2 ConfigurationTo configure the WiBox 2100E’s hostlist Host InformationPort Settings Serial SettingsTo configure a channel’s serial settings ChannelPack Control Flush Input Buffer Serial to NetworkFlush Output Buffer Network to Serial Connection Settings TCPTo configure a channel’s TCP settings Connect ProtocolConnect Mode Passive Connection Connect Mode Active Connection Endpoint ConfigurationCommon Options Connection Settings UDP Disconnect ModeTo configure a channel’s UDP settings Use Broadcast Datagram ModeDatagram Type Device Address TableWlan Configuration To configure the WiBox 2100E’s Wlan settingsWireless Network Configuration Wireless Network SecurityWPA Options Advanced SettingsWEP Options 802.11i/WPA2-Personal OptionsUpdating Settings Applying DefaultsTelnet or Serial Port Setup Mode Configuration Accessing Setup ModeTelnet Connection Exiting Setup Mode Telnet or Serial Port Setup Mode ConfigurationSerial Port Connection Network Mode Setup Mode Server ConfigurationServer Configuration Option IP AddressNetmask Number of Bits for Host Part Change Telnet Configuration PasswordSetup Mode Server Configuration Set DNS Server IP AddressDhcp Name Automatic Host MAC DetectionSetup Mode Channel Configuration Channel 1 OptionBaudrate Mode Option Interface ModeSetup Mode Channel Configuration Common I/F Mode Setting Binary HexFlow Control Option Hex FlowPort Number Port Numbers Reserved forConnect Mode Connect Mode OptionIncoming Connection ResponseActive Startup C28.10/12 Manual Connection Address ExampleC121.2.4.5/1 C0.0.0.0/0To enable the hostlist Autostart AutomaticHostlist Modem Mode Datagram TypeFull Verbose Modem Mode MessagesMessage Meaning Numeric ResponseSend the Escape Sequence +++ in Modem Mode Modem Mode Command FunctionShow IP addr after Ring Remote Port Auto Increment Source PortRemote IP Address DisConnModeFlush Mode Buffer Flushing Disconnect Mode Options10. Flush Mode Options Alternate Packing Algorithm Pack Control Enable Pack ControlOption Packing Interval DisConnTime Inactivity TimeoutSend Characters Trailing CharactersChannel Port Password Wlan SettingsTelnet Terminal Type WEP Display Current KeyTransmission Data Rate 802.11i/WPA2-PersonalFixed or Automatic Data Rate Minimum TX Data RateEnable Power Management Enable Soft AP RoamingMax TX Failures Setup Mode Advanced Settings Expert Settings OptionTCP Keepalive time in seconds ARP Cache timeout in secondsDisable Monitor Mode at bootup CPU PerformanceEnable Alternate MAC Security Settings OptionTCP Re-transmission Timeout Configurable Server Port NumberDisable Tftp Firmware Upgrade Disable SnmpDisable Telnet Setup Disable Port 77FE HexEnable Enhanced Password Disable Echo PortsEnable Encryption Enable EncryptionDefault Settings Option Channel 1 ConfigurationChannel 2 Configuration Expert Settings Security SettingsExit Configuration Mode Entering Monitor Mode via the Network Port Monitor ModeEntering Monitor Mode via the Serial Port Monitor Mode CommandsMonitor Mode G0, G1, ....,Ge, GfS0, S1,...,Se, Sf Response Meaning Obtaining Firmware Reloading Firmware Using Tftp Graphical User InterfaceUpdating Firmware To download new firmware from a computerUsing Tftp Command Line Interface Network UpgradeUpdating Firmware Wlan Country Setting To recover firmwareTo initialize the bridging feature Wireless BridgingConfiguring the WiBox 2100E in Bridging Mode MethodWireless Bridging Problems and Error Messages TroubleshootingDiagnostic LED States Problem/Message Reason SolutionTroubleshooting Entry addition failed 5 messageWiBox 2100E only Technical Support Technical Support USTechnical Support Europe, Middle East, and Africa Mounting Brackets Conversion Table Binary to Hexadecimal ConversionsConverting Binary to Hexadecimal Scientific CalculatorBinary to Hexadecimal Conversions Compliance Compliance InformationCompliance Regulatory InformationUSA Federal Communications Commission FCC Notice RoHS NoticeCanada Industry Canada Notice Antenna NoticeExposure of Humans to RF Fields Europe R&TTE Directive 99/5/EC, Wireless Notice Australia & New Zealand Wireless NoticeCountry Restriction