Lantronix 2100E manual Wireless Bridging

Page 7

Contents

Default Settings (Option 7) _______________________________________________ 72

Channel 1 Configuration______________________________________________ 72

Channel 2 Configuration______________________________________________ 72

WLAN Settings _____________________________________________________ 72

Expert Settings _____________________________________________________ 73

Security Settings____________________________________________________ 73

Exit Configuration Mode _________________________________________________ 74

9: Monitor Mode

75

Entering Monitor Mode via the Serial Port ___________________________________ 75

Entering Monitor Mode via the Network Port _________________________________ 75

Monitor Mode Commands________________________________________________ 75

10: Updating Firmware

78

Obtaining Firmware_____________________________________________________ 78

Reloading Firmware ____________________________________________________ 78

Using TFTP: Graphical User Interface ______________________________________ 78

Using TFTP: Command Line Interface ______________________________________ 79

Network Upgrade ______________________________________________________ 79

Recovering the Firmware Using the Serial Port and DeviceInstaller _______________ 79

WLAN Country Setting __________________________________________________ 80

11: Wireless Bridging

81

Configuring the WiBox 2100E in Bridging Mode_______________________________ 81

Method 1__________________________________________________________ 81

Method 2__________________________________________________________ 81

Method 3__________________________________________________________ 82

12: Troubleshooting

83

Diagnostic LED States __________________________________________________ 83

Problems and Error Messages ____________________________________________ 83

Technical Support ______________________________________________________ 86

A: Mounting Brackets

87

B: Binary to Hexadecimal Conversions

88

Converting Binary to Hexadecimal _________________________________________ 88

Conversion Table ___________________________________________________ 88

Scientific Calculator _________________________________________________ 88

C: Compliance

90

Compliance Information _________________________________________________ 90

Regulatory Information __________________________________________________ 91

USA Federal Communications Commission (FCC) Notice ___________________ 91

Canada – Industry Canada Notice ______________________________________ 92

Europe – R&TTE Directive 99/5/EC, Wireless Notice _______________________ 93

Australia & New Zealand – Wireless Notice_______________________________ 93

WiBox® 2100E Device Server User Guide

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents WiBox 2100E Device Server User Guide Lantronix, Inc Corporate Headquarters Warranty ContactsIntellectual Property Revision HistoryWiBox 2100E Device Server User Guide Table of Contents Contents Setup Mode Server ConfigurationSetup Mode Advanced Settings Wireless Bridging List of Figures Chapter Description Using This GuidePurpose and Audience Chapter SummaryAdditional Documentation Using This GuideDocument Description WiBox 2100E with IntroductionApplications Name Model Part NumbersSerial Tunneling Network Application ExamplesIntroduction Serial Tunneling Infrastructure Ad Hoc NetworkWiBox 2100E with Ethernet Configuration MethodsProtocol Support Ad Hoc WiBox 2100E ConnectionAddresses and Port Numbers Serial Connector PinoutsDB9M DTE Serial Connector WiBox 2100E LEDs Ethernet Connector PinoutsWiBox 2100E Network Interface LEDsTechnical Specifications Getting Started Installing the WiBox 2100EGetting Started Configuring the WiBox 2100EWEP CaseProperty Description 802.11i/WPA2-Personal Installing DeviceInstallerTo view the WiBox 2100E’s configuration settings Viewing the Current ConfigurationGetting Started Accessing Web Manager through a Web Browser Web Manager ConfigurationNetwork Mode Network ConfigurationNetwork Mode Configuration Web Manager ConfigurationSelect Obtain IP address automatically Automatic IP Address ConfigurationStatic IP Address Configuration Select Use the following IP configurationDuplex Ethernet ConfigurationAuto Negotiate SpeedTo configure the WiBox 2100E’s device server settings Server ConfigurationServer Configuration Advanced Hostlist ConfigurationHost Information Channel 1 and Channel 2 ConfigurationTo configure the WiBox 2100E’s hostlist Retry SettingsChannel Serial SettingsTo configure a channel’s serial settings Port SettingsFlush Input Buffer Serial to Network Pack ControlConnect Protocol Connection Settings TCPTo configure a channel’s TCP settings Flush Output Buffer Network to SerialConnect Mode Passive Connection Endpoint Configuration Connect Mode Active ConnectionCommon Options Disconnect Mode Connection Settings UDPTo configure a channel’s UDP settings Device Address Table Datagram ModeDatagram Type Use BroadcastTo configure the WiBox 2100E’s Wlan settings Wlan ConfigurationWireless Network Security Wireless Network Configuration802.11i/WPA2-Personal Options Advanced SettingsWEP Options WPA OptionsApplying Defaults Updating SettingsAccessing Setup Mode Telnet or Serial Port Setup Mode ConfigurationTelnet Connection Telnet or Serial Port Setup Mode Configuration Exiting Setup ModeSerial Port Connection IP Address Setup Mode Server ConfigurationServer Configuration Option Network ModeSet DNS Server IP Address Change Telnet Configuration PasswordSetup Mode Server Configuration Netmask Number of Bits for Host PartAutomatic Host MAC Detection Dhcp NameChannel 1 Option Setup Mode Channel ConfigurationBaudrate Common I/F Mode Setting Binary Hex Interface ModeSetup Mode Channel Configuration Mode OptionPort Numbers Reserved for FlowPort Number Flow Control Option HexConnect Mode Option Connect ModeResponse Incoming ConnectionActive Startup C0.0.0.0/0 Manual Connection Address ExampleC121.2.4.5/1 C28.10/12Autostart Automatic To enable the hostlistHostlist Datagram Type Modem ModeNumeric Response Modem Mode MessagesMessage Meaning Full VerboseModem Mode Command Function Send the Escape Sequence +++ in Modem ModeShow IP addr after Ring DisConnMode Auto Increment Source PortRemote IP Address Remote PortDisconnect Mode Options Flush Mode Buffer Flushing10. Flush Mode Options Pack Control Alternate Packing Algorithm Pack Control EnableOption Trailing Characters DisConnTime Inactivity TimeoutSend Characters Packing IntervalWlan Settings Channel Port PasswordTelnet Terminal Type Display Current Key WEPMinimum TX Data Rate 802.11i/WPA2-PersonalFixed or Automatic Data Rate Transmission Data RateEnable Soft AP Roaming Enable Power ManagementMax TX Failures Expert Settings Option Setup Mode Advanced SettingsCPU Performance ARP Cache timeout in secondsDisable Monitor Mode at bootup TCP Keepalive time in secondsConfigurable Server Port Number Security Settings OptionTCP Re-transmission Timeout Enable Alternate MACDisable Port 77FE Hex Disable SnmpDisable Telnet Setup Disable Tftp Firmware UpgradeEnable Encryption Disable Echo PortsEnable Encryption Enable Enhanced PasswordChannel 1 Configuration Default Settings OptionChannel 2 Configuration Security Settings Expert SettingsExit Configuration Mode Monitor Mode Commands Monitor ModeEntering Monitor Mode via the Serial Port Entering Monitor Mode via the Network PortG0, G1, ....,Ge, Gf Monitor ModeS0, S1,...,Se, Sf Response Meaning To download new firmware from a computer Using Tftp Graphical User InterfaceUpdating Firmware Obtaining Firmware Reloading FirmwareNetwork Upgrade Using Tftp Command Line InterfaceUpdating Firmware To recover firmware Wlan Country SettingMethod Wireless BridgingConfiguring the WiBox 2100E in Bridging Mode To initialize the bridging featureWireless Bridging Problem/Message Reason Solution TroubleshootingDiagnostic LED States Problems and Error MessagesEntry addition failed 5 message TroubleshootingWiBox 2100E only Technical Support US Technical SupportTechnical Support Europe, Middle East, and Africa Mounting Brackets Scientific Calculator Binary to Hexadecimal ConversionsConverting Binary to Hexadecimal Conversion TableBinary to Hexadecimal Conversions Compliance Information ComplianceRoHS Notice Regulatory InformationUSA Federal Communications Commission FCC Notice ComplianceAntenna Notice Canada Industry Canada NoticeExposure of Humans to RF Fields Australia & New Zealand Wireless Notice Europe R&TTE Directive 99/5/EC, Wireless NoticeCountry Restriction
Top Page Image Contents