Lantronix 2100E manual Auto Increment Source Port, Remote IP Address, Remote Port, DisConnMode

Page 59

7: Setup Mode: Channel Configuration

Auto Increment Source Port

Auto increment source port (N) ? _

Y (Yes) auto increment the source port. The WiBox 2100E increments the port number used with each new connection.

Remote IP Address

This is the destination IP address used with an outgoing connection.

Remote IP Address : (000) (000) (000) (000)_

Note: This option does not display when Hostlist is enabled from the ConnectMode prompt (see Connect Mode on page 52 for more information).

Remote Port

You must set the remote TCP port number for the unit to make outgoing connections. This parameter defines the port number on the target host to which a connection is attempted.

Remote Port (0) ? _

To connect an ASCII terminal to a host using the unit for login purposes, use the remote port number 23 (Internet standard port number for Telnet services).

Note: This option does not display when Hostlist is enabled from the ConnectMode prompt (see Connect Mode on page 52 for more information).

DisConnMode

This setting determines the conditions under which the unit will cause a network connection to terminate. The default setting is 00.

DisConnMode (00) ? _

Notes:

In DisConnMode (Disconnect Mode), Modem Control In either drops the connection or is ignored.

Note: All bit positions in the table that are blank represent “don’t care” bits for that particular option; they can be set to either a 0 or 1 value.

WiBox® 2100E Device Server User Guide

59

Image 59
Contents WiBox 2100E Device Server User Guide Lantronix, Inc Corporate Headquarters Warranty ContactsIntellectual Property Revision HistoryWiBox 2100E Device Server User Guide Table of Contents Contents Setup Mode Server ConfigurationSetup Mode Advanced Settings Wireless Bridging List of Figures Chapter Description Using This GuidePurpose and Audience Chapter SummaryDocument Description Using This GuideAdditional Documentation WiBox 2100E with IntroductionApplications Name Model Part NumbersIntroduction Application ExamplesSerial Tunneling Network Serial Tunneling Infrastructure Ad Hoc NetworkWiBox 2100E with Ethernet Configuration MethodsProtocol Support Ad Hoc WiBox 2100E ConnectionAddresses and Port Numbers Serial Connector PinoutsDB9M DTE Serial Connector WiBox 2100E LEDs Ethernet Connector PinoutsWiBox 2100E Network Interface LEDsTechnical Specifications Getting Started Installing the WiBox 2100EGetting Started Configuring the WiBox 2100EWEP CaseProperty Description 802.11i/WPA2-Personal Installing DeviceInstallerTo view the WiBox 2100E’s configuration settings Viewing the Current ConfigurationGetting Started Accessing Web Manager through a Web Browser Web Manager ConfigurationNetwork Mode Network ConfigurationNetwork Mode Configuration Web Manager ConfigurationSelect Obtain IP address automatically Automatic IP Address ConfigurationStatic IP Address Configuration Select Use the following IP configurationDuplex Ethernet ConfigurationAuto Negotiate SpeedServer Configuration Server ConfigurationTo configure the WiBox 2100E’s device server settings Advanced Hostlist ConfigurationHost Information Channel 1 and Channel 2 ConfigurationTo configure the WiBox 2100E’s hostlist Retry SettingsChannel Serial SettingsTo configure a channel’s serial settings Port SettingsFlush Input Buffer Serial to Network Pack ControlConnect Protocol Connection Settings TCPTo configure a channel’s TCP settings Flush Output Buffer Network to SerialConnect Mode Passive Connection Common Options Connect Mode Active ConnectionEndpoint Configuration To configure a channel’s UDP settings Connection Settings UDPDisconnect Mode Device Address Table Datagram ModeDatagram Type Use BroadcastTo configure the WiBox 2100E’s Wlan settings Wlan ConfigurationWireless Network Security Wireless Network Configuration802.11i/WPA2-Personal Options Advanced SettingsWEP Options WPA OptionsApplying Defaults Updating SettingsTelnet Connection Telnet or Serial Port Setup Mode ConfigurationAccessing Setup Mode Serial Port Connection Exiting Setup ModeTelnet or Serial Port Setup Mode Configuration IP Address Setup Mode Server ConfigurationServer Configuration Option Network ModeSet DNS Server IP Address Change Telnet Configuration PasswordSetup Mode Server Configuration Netmask Number of Bits for Host PartAutomatic Host MAC Detection Dhcp NameBaudrate Setup Mode Channel ConfigurationChannel 1 Option Common I/F Mode Setting Binary Hex Interface ModeSetup Mode Channel Configuration Mode OptionPort Numbers Reserved for FlowPort Number Flow Control Option HexConnect Mode Option Connect ModeActive Startup Incoming ConnectionResponse C0.0.0.0/0 Manual Connection Address ExampleC121.2.4.5/1 C28.10/12Hostlist To enable the hostlistAutostart Automatic Datagram Type Modem ModeNumeric Response Modem Mode MessagesMessage Meaning Full VerboseShow IP addr after Ring Send the Escape Sequence +++ in Modem ModeModem Mode Command Function DisConnMode Auto Increment Source PortRemote IP Address Remote Port10. Flush Mode Options Flush Mode Buffer FlushingDisconnect Mode Options Option Alternate Packing Algorithm Pack Control EnablePack Control Trailing Characters DisConnTime Inactivity TimeoutSend Characters Packing IntervalTelnet Terminal Type Channel Port PasswordWlan Settings Display Current Key WEPMinimum TX Data Rate 802.11i/WPA2-PersonalFixed or Automatic Data Rate Transmission Data RateMax TX Failures Enable Power ManagementEnable Soft AP Roaming Expert Settings Option Setup Mode Advanced SettingsCPU Performance ARP Cache timeout in secondsDisable Monitor Mode at bootup TCP Keepalive time in secondsConfigurable Server Port Number Security Settings OptionTCP Re-transmission Timeout Enable Alternate MACDisable Port 77FE Hex Disable SnmpDisable Telnet Setup Disable Tftp Firmware UpgradeEnable Encryption Disable Echo PortsEnable Encryption Enable Enhanced PasswordChannel 2 Configuration Default Settings OptionChannel 1 Configuration Security Settings Expert SettingsExit Configuration Mode Monitor Mode Commands Monitor ModeEntering Monitor Mode via the Serial Port Entering Monitor Mode via the Network PortS0, S1,...,Se, Sf Monitor ModeG0, G1, ....,Ge, Gf Response Meaning To download new firmware from a computer Using Tftp Graphical User InterfaceUpdating Firmware Obtaining Firmware Reloading FirmwareUpdating Firmware Using Tftp Command Line InterfaceNetwork Upgrade To recover firmware Wlan Country SettingMethod Wireless BridgingConfiguring the WiBox 2100E in Bridging Mode To initialize the bridging featureWireless Bridging Problem/Message Reason Solution TroubleshootingDiagnostic LED States Problems and Error MessagesEntry addition failed 5 message TroubleshootingWiBox 2100E only Technical Support Europe, Middle East, and Africa Technical SupportTechnical Support US Mounting Brackets Scientific Calculator Binary to Hexadecimal ConversionsConverting Binary to Hexadecimal Conversion TableBinary to Hexadecimal Conversions Compliance Information ComplianceRoHS Notice Regulatory InformationUSA Federal Communications Commission FCC Notice ComplianceExposure of Humans to RF Fields Canada Industry Canada NoticeAntenna Notice Country Restriction Europe R&TTE Directive 99/5/EC, Wireless NoticeAustralia & New Zealand Wireless Notice