Lantronix 2100E manual Mounting Brackets

Page 87

A: Mounting Brackets

The following drawings provide dimensions of the brackets for mounting the WiBox 2100E device server.

WiBox® 2100E Device Server User Guide

87

Image 87

Contents WiBox 2100E Device Server User Guide Lantronix, Inc Corporate Headquarters Warranty ContactsIntellectual Property Revision HistoryWiBox 2100E Device Server User Guide Table of Contents Contents Setup Mode Server ConfigurationSetup Mode Advanced Settings Wireless Bridging List of Figures Chapter Description Using This GuidePurpose and Audience Chapter SummaryUsing This Guide Additional DocumentationDocument Description WiBox 2100E with IntroductionApplications Name Model Part NumbersApplication Examples Serial Tunneling NetworkIntroduction Serial Tunneling Infrastructure Ad Hoc NetworkWiBox 2100E with Ethernet Configuration MethodsProtocol Support Ad Hoc WiBox 2100E ConnectionAddresses and Port Numbers Serial Connector PinoutsDB9M DTE Serial Connector WiBox 2100E LEDs Ethernet Connector PinoutsWiBox 2100E Network Interface LEDsTechnical Specifications Getting Started Installing the WiBox 2100EGetting Started Configuring the WiBox 2100EWEP CaseProperty Description 802.11i/WPA2-Personal Installing DeviceInstallerTo view the WiBox 2100E’s configuration settings Viewing the Current ConfigurationGetting Started Accessing Web Manager through a Web Browser Web Manager ConfigurationNetwork Mode Network ConfigurationNetwork Mode Configuration Web Manager ConfigurationSelect Obtain IP address automatically Automatic IP Address ConfigurationStatic IP Address Configuration Select Use the following IP configurationDuplex Ethernet ConfigurationAuto Negotiate SpeedServer Configuration To configure the WiBox 2100E’s device server settingsServer Configuration Advanced Hostlist ConfigurationHost Information Channel 1 and Channel 2 ConfigurationTo configure the WiBox 2100E’s hostlist Retry SettingsChannel Serial SettingsTo configure a channel’s serial settings Port SettingsFlush Input Buffer Serial to Network Pack ControlConnect Protocol Connection Settings TCPTo configure a channel’s TCP settings Flush Output Buffer Network to SerialConnect Mode Passive Connection Connect Mode Active Connection Endpoint ConfigurationCommon Options Connection Settings UDP Disconnect ModeTo configure a channel’s UDP settings Device Address Table Datagram ModeDatagram Type Use BroadcastTo configure the WiBox 2100E’s Wlan settings Wlan ConfigurationWireless Network Security Wireless Network Configuration802.11i/WPA2-Personal Options Advanced SettingsWEP Options WPA OptionsApplying Defaults Updating SettingsTelnet or Serial Port Setup Mode Configuration Accessing Setup ModeTelnet Connection Exiting Setup Mode Telnet or Serial Port Setup Mode ConfigurationSerial Port Connection IP Address Setup Mode Server ConfigurationServer Configuration Option Network ModeSet DNS Server IP Address Change Telnet Configuration PasswordSetup Mode Server Configuration Netmask Number of Bits for Host PartAutomatic Host MAC Detection Dhcp NameSetup Mode Channel Configuration Channel 1 OptionBaudrate Common I/F Mode Setting Binary Hex Interface ModeSetup Mode Channel Configuration Mode OptionPort Numbers Reserved for FlowPort Number Flow Control Option HexConnect Mode Option Connect ModeIncoming Connection ResponseActive Startup C0.0.0.0/0 Manual Connection Address ExampleC121.2.4.5/1 C28.10/12To enable the hostlist Autostart AutomaticHostlist Datagram Type Modem ModeNumeric Response Modem Mode MessagesMessage Meaning Full VerboseSend the Escape Sequence +++ in Modem Mode Modem Mode Command FunctionShow IP addr after Ring DisConnMode Auto Increment Source PortRemote IP Address Remote PortFlush Mode Buffer Flushing Disconnect Mode Options10. Flush Mode Options Alternate Packing Algorithm Pack Control Enable Pack ControlOption Trailing Characters DisConnTime Inactivity TimeoutSend Characters Packing IntervalChannel Port Password Wlan SettingsTelnet Terminal Type Display Current Key WEPMinimum TX Data Rate 802.11i/WPA2-PersonalFixed or Automatic Data Rate Transmission Data RateEnable Power Management Enable Soft AP RoamingMax TX Failures Expert Settings Option Setup Mode Advanced SettingsCPU Performance ARP Cache timeout in secondsDisable Monitor Mode at bootup TCP Keepalive time in secondsConfigurable Server Port Number Security Settings OptionTCP Re-transmission Timeout Enable Alternate MACDisable Port 77FE Hex Disable SnmpDisable Telnet Setup Disable Tftp Firmware UpgradeEnable Encryption Disable Echo PortsEnable Encryption Enable Enhanced PasswordDefault Settings Option Channel 1 ConfigurationChannel 2 Configuration Security Settings Expert SettingsExit Configuration Mode Monitor Mode Commands Monitor ModeEntering Monitor Mode via the Serial Port Entering Monitor Mode via the Network PortMonitor Mode G0, G1, ....,Ge, GfS0, S1,...,Se, Sf Response Meaning To download new firmware from a computer Using Tftp Graphical User InterfaceUpdating Firmware Obtaining Firmware Reloading FirmwareUsing Tftp Command Line Interface Network UpgradeUpdating Firmware To recover firmware Wlan Country SettingMethod Wireless BridgingConfiguring the WiBox 2100E in Bridging Mode To initialize the bridging featureWireless Bridging Problem/Message Reason Solution TroubleshootingDiagnostic LED States Problems and Error MessagesEntry addition failed 5 message TroubleshootingWiBox 2100E only Technical Support Technical Support USTechnical Support Europe, Middle East, and Africa Mounting Brackets Scientific Calculator Binary to Hexadecimal ConversionsConverting Binary to Hexadecimal Conversion TableBinary to Hexadecimal Conversions Compliance Information ComplianceRoHS Notice Regulatory InformationUSA Federal Communications Commission FCC Notice ComplianceCanada Industry Canada Notice Antenna NoticeExposure of Humans to RF Fields Europe R&TTE Directive 99/5/EC, Wireless Notice Australia & New Zealand Wireless NoticeCountry Restriction