Lantronix 2100E manual Connect Mode Passive Connection

Page 36

4: Web Manager Configuration

Figure 4-6. TCP Connection Settings

Connect Mode: Passive Connection

Accept Incoming

Select Yes to accept incoming connections.

 

 

Password Required

Determines whether a password is required for an incoming passive

 

connection. This field is not available when a password is set for Telnet

 

mode. The default setting is No.

 

 

Password

If Password Required was set to Yes, enter the password for passive

 

connections.

 

 

Modem Escape

Disable or enable the unit's ability to send the escape sequence. The

Sequence Pass

default is Y (Yes) (send the escape sequence).

Through

 

 

 

WiBox® 2100E Device Server User Guide

36

Page 35 Page 37
Image 36
Page 35 Page 37
Contents WiBox 2100E Device Server User Guide Warranty Contacts Intellectual PropertyRevision History Lantronix, Inc Corporate HeadquartersWiBox 2100E Device Server User Guide Table of Contents Setup Mode Server Configuration ContentsSetup Mode Advanced Settings Wireless Bridging List of Figures Using This Guide Purpose and AudienceChapter Summary Chapter DescriptionUsing This Guide Additional DocumentationDocument Description Introduction ApplicationsName Model Part Numbers WiBox 2100E withApplication Examples Serial Tunneling NetworkIntroduction Ad Hoc Network Serial Tunneling InfrastructureConfiguration Methods Protocol SupportAd Hoc WiBox 2100E Connection WiBox 2100E with EthernetSerial Connector Pinouts Addresses and Port NumbersDB9M DTE Serial Connector Ethernet Connector Pinouts WiBox 2100E Network InterfaceLEDs WiBox 2100E LEDsTechnical Specifications Installing the WiBox 2100E Getting StartedConfiguring the WiBox 2100E Getting StartedCase WEPProperty Description Installing DeviceInstaller 802.11i/WPA2-PersonalViewing the Current Configuration To view the WiBox 2100E’s configuration settingsGetting Started Web Manager Configuration Accessing Web Manager through a Web BrowserNetwork Configuration Network Mode ConfigurationWeb Manager Configuration Network ModeAutomatic IP Address Configuration Static IP Address ConfigurationSelect Use the following IP configuration Select Obtain IP address automaticallyEthernet Configuration Auto NegotiateSpeed DuplexServer Configuration To configure the WiBox 2100E’s device server settingsServer Configuration Hostlist Configuration AdvancedChannel 1 and Channel 2 Configuration To configure the WiBox 2100E’s hostlistRetry Settings Host InformationSerial Settings To configure a channel’s serial settingsPort Settings ChannelPack Control Flush Input Buffer Serial to NetworkConnection Settings TCP To configure a channel’s TCP settingsFlush Output Buffer Network to Serial Connect ProtocolConnect Mode Passive Connection Connect Mode Active Connection Endpoint ConfigurationCommon Options Connection Settings UDP Disconnect ModeTo configure a channel’s UDP settings Datagram Mode Datagram TypeUse Broadcast Device Address TableWlan Configuration To configure the WiBox 2100E’s Wlan settingsWireless Network Configuration Wireless Network SecurityAdvanced Settings WEP OptionsWPA Options 802.11i/WPA2-Personal OptionsUpdating Settings Applying DefaultsTelnet or Serial Port Setup Mode Configuration Accessing Setup ModeTelnet Connection Exiting Setup Mode Telnet or Serial Port Setup Mode ConfigurationSerial Port Connection Setup Mode Server Configuration Server Configuration OptionNetwork Mode IP AddressChange Telnet Configuration Password Setup Mode Server ConfigurationNetmask Number of Bits for Host Part Set DNS Server IP AddressDhcp Name Automatic Host MAC DetectionSetup Mode Channel Configuration Channel 1 OptionBaudrate Interface Mode Setup Mode Channel ConfigurationMode Option Common I/F Mode Setting Binary HexFlow Port NumberFlow Control Option Hex Port Numbers Reserved forConnect Mode Connect Mode OptionIncoming Connection ResponseActive Startup Manual Connection Address Example C121.2.4.5/1C28.10/12 C0.0.0.0/0To enable the hostlist Autostart AutomaticHostlist Modem Mode Datagram TypeModem Mode Messages Message MeaningFull Verbose Numeric ResponseSend the Escape Sequence +++ in Modem Mode Modem Mode Command FunctionShow IP addr after Ring Auto Increment Source Port Remote IP AddressRemote Port DisConnModeFlush Mode Buffer Flushing Disconnect Mode Options10. Flush Mode Options Alternate Packing Algorithm Pack Control Enable Pack ControlOption DisConnTime Inactivity Timeout Send CharactersPacking Interval Trailing CharactersChannel Port Password Wlan SettingsTelnet Terminal Type WEP Display Current Key802.11i/WPA2-Personal Fixed or Automatic Data RateTransmission Data Rate Minimum TX Data RateEnable Power Management Enable Soft AP RoamingMax TX Failures Setup Mode Advanced Settings Expert Settings OptionARP Cache timeout in seconds Disable Monitor Mode at bootupTCP Keepalive time in seconds CPU PerformanceSecurity Settings Option TCP Re-transmission TimeoutEnable Alternate MAC Configurable Server Port NumberDisable Snmp Disable Telnet SetupDisable Tftp Firmware Upgrade Disable Port 77FE HexDisable Echo Ports Enable EncryptionEnable Enhanced Password Enable EncryptionDefault Settings Option Channel 1 ConfigurationChannel 2 Configuration Expert Settings Security SettingsExit Configuration Mode Monitor Mode Entering Monitor Mode via the Serial PortEntering Monitor Mode via the Network Port Monitor Mode CommandsMonitor Mode G0, G1, ....,Ge, GfS0, S1,...,Se, Sf Response Meaning Using Tftp Graphical User Interface Updating FirmwareObtaining Firmware Reloading Firmware To download new firmware from a computerUsing Tftp Command Line Interface Network UpgradeUpdating Firmware Wlan Country Setting To recover firmwareWireless Bridging Configuring the WiBox 2100E in Bridging ModeTo initialize the bridging feature MethodWireless Bridging Troubleshooting Diagnostic LED StatesProblems and Error Messages Problem/Message Reason SolutionTroubleshooting Entry addition failed 5 messageWiBox 2100E only Technical Support Technical Support USTechnical Support Europe, Middle East, and Africa Mounting Brackets Binary to Hexadecimal Conversions Converting Binary to HexadecimalConversion Table Scientific CalculatorBinary to Hexadecimal Conversions Compliance Compliance InformationRegulatory Information USA Federal Communications Commission FCC NoticeCompliance RoHS NoticeCanada Industry Canada Notice Antenna NoticeExposure of Humans to RF Fields Europe R&TTE Directive 99/5/EC, Wireless Notice Australia & New Zealand Wireless NoticeCountry Restriction
Top Page Image Contents