Westell Technologies 2100 manual Simultaneous Connection via 10/100 Base-T Ethernet and USB

Page 10

User Guide

WireSpeed Dual Connect NAT Router

5.4.3Router Installation via 10/100 Base-T Ethernet and USB (Simultaneous Installation)

The Dual Connect Router supports simultaneous use of 10/100 Base-T Ethernet and USB ports. The following instructions explain how to install your Router using both Ethernet and USB ports.

~

1. Connect the power supply cord to the power connector marked 12V on the rear panel of the Router. Plug the other end of the power supply cord into a surge-protected AC wall socket.

2.Connect the DSL phone cable from the jack on the rear panel of the Router marked to the DSL-equipped telephone line jack on the wall. IMPORTANT: Do not use a DSL filter on this connection. You must use the phone cord that was provided with the Router kit.

3.Connect the Ethernet cable from the Ethernet jack markedon the rear panel of the Router to the Ethernet port on your computer.

4.Connect the USB cable from the USB connector marked on the rear panel of the Router to the USB port on the PC.

Congratulations! You have completed the simultaneous hardware (Ethernet and USB) installation for your Dual Connect NAT Router. Refer to your Internet service provider’s instructions for installing subscriber software and connecting to the Internet. You must now go to Section 6 to begin the USB software installation. (No software installation is required when using an Ethernet connection.)

NOTE: Figure 3 illustrates a USB connection from the Dual Connect Router to a laptop. However, you may connect the USB cable from the Dual Connect Router to any PC that has the minimum system requirements installed and supports USB connectivity.

Plug the USB jack into an available USB connector on the PC.

USB

Connector

Figure 3. Simultaneous Connection via 10/100 Base-T Ethernet and USB

030-300198 Rev. D

8

March 2003

Image 10

Contents Wirespeed Dual Connect NAT Router Model User GuideContents Safety Instructions Product DescriptionRegulatory Information FCC Compliance NoteCanada Certification Notice Minimum System Requirements for USB Installation System RequirementsRouter Installations Installation InformationInstallation Requirements Before you beginRouter Installation via 10/100 Base-T Ethernet Connection via 10/100 Base-T EthernetRouter Installation via USB Connection via USBSimultaneous Connection via 10/100 Base-T Ethernet and USB LED States and Descriptions LED IndicatorsCable Connectors and Switch Locations State Description12V Connector DescriptionsUSB Series B Connector Pinouts Name Description Cable Color DSL Pinouts DescriptionInstalling the Westell CD-ROM Installing the USB DriversInstalling the USB Drivers for Windows Windows Location of Hardware Device Driver Loading Device Driver Windows Restart the Computer Installing the USB Drivers for Windows ME Windows MEFound New Hardware Installing the USB Driver for Windows Welcome to Install Device DriverLocate Driver Files Driver Files Search Results Installing the USB Driver for Windows XP Restart Your ComputerWindows XP Configuring the Router for Internet Connection Setting Up an Account ProfileWestell 030-300198 Rev. D User Guide User Guide Establishing a DSL Sync Establishing a PPP Session Disconnecting a PPP Session Configuring NAT Service optional User Guide User Guide Opening the System Preference Screen Setting UP Macintosh OSChoosing the Network Preferences Creating a New Location Naming the New LocationSelecting the Ethernet Configuration Checking the IP ConnectionCreating a User Account Setting UP Advanced Configuration HomeAdding Account Profiles Status Connection Summary About DSL Connection InformationConfiguration VC Configuration VPI User Guide VC 1 Configuration VC x PPPoE SettingsUser Assigned DNS DNS ConfigurationDNS Server Static Host AssignmentAdding a New Host Name and IP Address Dhcp Configuration Disabling the Dhcp Server Enabling the Dhcp Server Private LAN Configuration User Guide Public LAN Configuration Check Private LAN Dhcp SettingsUser GuideWireSpeed Dual Connect NAT Router Check Public LAN Dhcp Settings Single Static IP Configuration Enabling Single Static IPUser Guide User GuideWireSpeed Dual Connect NAT Router Disabling Single Static IP User GuideWireSpeed Dual Connect NAT Router Service Configuration Creating a New Service ProfileUser Guide Editing a Service Profile Close Adding a NAT Service to a Profile User Guide Firewall Configuration 030-300198 Rev. D User Guide ATM Loopbacks Advanced Service Configuration Port Forwarding Ranges of Ports Adding Port Forwarding PortsPort Forwarding Trigger Ports Adding Local Trigger Ports Static NATEnabling Static NAT Disabling Static NAT User Guide Maintenance Backup/Store Firewall Log Change Password Remote Access URLUpdate Device Actual information displayed in this screen may vary User Guide User Guide Screen below shows that the Router is being reset Troubleshooting System Self Tests Connection/StatusTest Description / Test Results Diagnostic Logs Running a DiagnosticUser Guide Saving the Diagnostic Log File WAN VC Statistics VPI/VCIEthernet Port Statistics Transceiver Statistics Transceiver Information-Down Stream/Up Stream PathUSB Port Statistics LAN Statistics About HelpATM Loopback Change Administration Password Backup/RestoreConnection Summary Diagnostics Help PPPoEPing ISPs Router Self TestPing ISP’s Router End of Diagnostic Help Screens Edit Connection Profiles DNS Configuration ScreenEdit Connection Profiles Firewall Settings Firewall SettingsHome LAN Configuration LAN ConfigurationProtocol Private LANPublic LAN Single Static IP Software UpgradeSoftware Upgrade Single Static IPVPI/VCI VC Configuration ScreenUser Name User NameNAT Services DNSApplication/Game Port/Protocol 22 TCP/UDP VPN Protocol Comments Technical Support Information Warranty and RepairsWarranty RepairsProduct Specifications Connectors Power SupplyPower Consumption SafetySoftware License Agreement Publication Information Trademarks