Westell Technologies 2100 manual Check Public LAN Dhcp Settings

Page 57

User Guide

WireSpeed Dual Connect NAT Router

If you selected Public LAN Enable, or if you made other changes in the Public LAN Configuration screen and clicked on save, the following pop-up screen will be displayed. Click on OK to save the new settings. If you click on Cancel, your new settings will not take affect.

NOTE: DHCP Lease Time is displayed in the following format: (dd:hh:mm:ss)*. (This value must be greater than 10 seconds.) The default = 01:00:00:00. Seconds must be between 0 and 59, minutes must be between 0 and 59, and hours must be between 0 and 23.

*(dd = days, hh = hours, mm = minutes, ss = seconds).

If the settings you have entered in the Public LAN Configuration screen are incorrect, the following warnings messages may be displayed via pop-up screens. If this occurs, check settings in the Public LAN Configuration screen.

Warning Message

Check Public LAN DHCP Settings

Start Address is not part of the Subnet

Check the value in the DHCP Start Address field

End Address is not part of the Subnet

Check the value in the DHCP End Address field

End Address is below the Start Address

Check the value in the DHCP End Address field

Lease time must be greater than 10 seconds

Check the values in the DHCP Lease Time fields

Seconds must be between 0 and 53

Check the Seconds field at DHCP Lease Time

Minutes must be between 0 and 59

Check the Minutes field at DHCP Lease Time

Hours must be between 0 and 23

Check the Hours field at DHCP Lease Time

If you clicked on OK in the Load new Public LAN configuration? pop-up screen, the following pop-up screen will be displayed. Click on OK. This will allow the modem to be reset, and the new configuration will take affect.

030-300198 Rev. D

55

March 2003

Image 57
Contents User Guide Wirespeed Dual Connect NAT Router ModelContents Product Description Safety InstructionsFCC Compliance Note Regulatory InformationCanada Certification Notice System Requirements Minimum System Requirements for USB InstallationInstallation Requirements Installation InformationRouter Installations Before you beginConnection via 10/100 Base-T Ethernet Router Installation via 10/100 Base-T EthernetConnection via USB Router Installation via USBSimultaneous Connection via 10/100 Base-T Ethernet and USB Cable Connectors and Switch Locations LED IndicatorsLED States and Descriptions State DescriptionUSB Series B Connector Pinouts Name Description Cable Color Connector Descriptions12V DSL Pinouts DescriptionInstalling the USB Drivers Installing the Westell CD-ROMInstalling the USB Drivers for Windows Windows Location of Hardware Device Driver Loading Device Driver Windows Restart the Computer Windows ME Installing the USB Drivers for Windows MEFound New Hardware Welcome to Install Device Driver Installing the USB Driver for WindowsLocate Driver Files Driver Files Search Results Restart Your Computer Installing the USB Driver for Windows XPWindows XP Setting Up an Account Profile Configuring the Router for Internet ConnectionWestell 030-300198 Rev. D User Guide User Guide Establishing a DSL Sync Establishing a PPP Session Disconnecting a PPP Session Configuring NAT Service optional User Guide User Guide Setting UP Macintosh OS Opening the System Preference ScreenChoosing the Network Preferences Naming the New Location Creating a New LocationChecking the IP Connection Selecting the Ethernet ConfigurationCreating a User Account Home Setting UP Advanced ConfigurationAdding Account Profiles Status Connection Summary DSL Connection Information AboutConfiguration VC Configuration VPI User Guide VC x PPPoE Settings VC 1 ConfigurationDNS Server DNS ConfigurationUser Assigned DNS Static Host AssignmentAdding a New Host Name and IP Address Dhcp Configuration Disabling the Dhcp Server Enabling the Dhcp Server Private LAN Configuration User Guide Check Private LAN Dhcp Settings Public LAN ConfigurationUser GuideWireSpeed Dual Connect NAT Router Check Public LAN Dhcp Settings Enabling Single Static IP Single Static IP ConfigurationUser Guide User GuideWireSpeed Dual Connect NAT Router Disabling Single Static IP User GuideWireSpeed Dual Connect NAT Router Creating a New Service Profile Service ConfigurationUser Guide Editing a Service Profile Close Adding a NAT Service to a Profile User Guide Firewall Configuration 030-300198 Rev. D User Guide ATM Loopbacks Advanced Service Configuration Adding Port Forwarding Ports Port Forwarding Ranges of PortsPort Forwarding Trigger Ports Static NAT Adding Local Trigger PortsEnabling Static NAT Disabling Static NAT User Guide Maintenance Backup/Store Firewall Log Change Password URL Remote AccessUpdate Device Actual information displayed in this screen may vary User Guide User Guide Screen below shows that the Router is being reset Connection/Status Troubleshooting System Self TestsTest Description / Test Results Running a Diagnostic Diagnostic LogsUser Guide Saving the Diagnostic Log File VPI/VCI WAN VC StatisticsEthernet Port Statistics Transceiver Information-Down Stream/Up Stream Path Transceiver StatisticsUSB Port Statistics LAN Statistics Help AboutATM Loopback Backup/Restore Change Administration PasswordConnection Summary PPPoE Diagnostics HelpSelf Test Ping ISPs RouterPing ISP’s Router End of Diagnostic Help Screens DNS Configuration Screen Edit Connection ProfilesEdit Connection Profiles Firewall Settings Firewall SettingsHome LAN Configuration LAN ConfigurationPrivate LAN ProtocolPublic LAN Software Upgrade Software UpgradeSingle Static IP Single Static IPUser Name VC Configuration ScreenVPI/VCI User NameDNS NAT ServicesApplication/Game Port/Protocol 22 TCP/UDP VPN Protocol Comments Warranty Warranty and RepairsTechnical Support Information RepairsProduct Specifications Power Consumption Power SupplyConnectors SafetySoftware License Agreement Trademarks Publication Information