RAD Data comm operation manual Configuring RIC-155, To configure RIC-155

Page 12

Quick Start Guide	RIC-155Installation and Operation Manual

4. When the ALM LED (red) starts blinking, press <Enter> several times.

RIC-155 automatically adjusts itself to the current terminal baud rate and responds with a string of dots.

5. Type several dots.

When the hardware initialization is completed, the SIG and ALM LEDs flash rapidly six times.

6.Press <Enter> to display the user name and password entry form.

7.Enter your user name and password and proceed with the management session.

Note The RIC-155 default user names are SU and USER, default password is 1234.

Configuring RIC-155

The management software provides a Quick Setup menu, which includes the most basic parameters necessary for configuration.

To configure RIC-155:

•From the Quick Setup menu (Main > Configuration > Quick Setup), configure the following parameters:

Master Clock

Host IP address

Host IP mask

Default Gateway

Host Tagging

Host VLAN ID

Host VLAN Priority

Forwarding Mode

Physical Port Management Access

SDH/SONET frame type.

2	Configuring RIC-155

Image 12

Contents RIC-155 Page RIC-155 Limited Warranty General Safety Instructions Please observe the following precautionsGeneral Safety Practices Connection of AC MainsConnection of DC Mains Ports Safety Status Connection of Data and Telecommunications CablesElectromagnetic Compatibility EMC Canadian Emission Requirements ConventionsSafety Manufacturers Name Manufacturers AddressProduct Name Supplementary InformationInstalling RIC-155 Configuring RIC-155Quick Start Guide Configuring RIC-155 To configure RIC-155Contents Troubleshooting and Diagnostics Appendix A. Connector Wiring Appendix B. Traffic SeparationChapter Introduction OverviewVersions ApplicationFeatures 10/100BaseT InterfaceSTM-1/OC-3c Interface Fiber Optic Interface OptionsAlarm Relay ManagementInternal Bridge Status ReportingPhysical Description RIC-155 3D ViewRIC-155 Block Diagram Functional DescriptionTechnical Specifications Alarm Types Major and minor Connector DB-9, female Temperature 50C / 32-122F Humidity Up to 90%, non-condensingIntroduction Chapter Installation and Setup IntroductionSite Requirements and Prerequisites Package Contents Connecting the Interface CablesConnecting the Power Cable Connecting AC PowerConnecting DC Power Connecting the Power Cable Controls and Indicators Chapter OperationTurning On RIC-155 To turn on RIC-155RIC-155 Normal Indicator Status Indicator StatusRIC-155 LEDs Name Function LocationDefault Settings RIC-155 Default SettingsConfiguration Alternatives Parameter Default ValueManaging RIC-155 via Terminal Port UplinkManaging RIC-155 via Ethernet Ports Preparing the TerminalStarting Terminal Session for a First Time To prepare RIC-155 for network managementTo start a ConfiguRAD session Loging on To enter the user name and passwordNavigating the Management Menus Menu MapTo choose an option ConfiguRAD session Choosing OptionsCorrecting Entries To choose an option terminal sessionTurning Off RIC-155 Navigating TablesLogging Out Operation Turning Off RIC-155 Chapter Configuration Configuring RIC-155 for ManagementTo access the Configuration menu To access the Management menuEntering Device Information To enter device informationConfiguring the Host Parameters To define the IP parametersConfiguring the Network Managers To configure the network managersControlling the Management Access To define the management access methodConfiguring the RIC-155 for Operation To enable or disable management portsConfiguring the Clock Source Configuring Control Port ParametersEnabling and Disabling Pop-up Alarms Configuring the Security TimeoutChanging the Control Port Data Rate Configuring the Physical Ports Configuring the Ethernet InterfaceConfiguring the STM-1/OC-3c Interface 10E-3,10E-4,10E-5 10E-5,10E-6,10E-7,10E-8,10E-9J1 Path Trace Uplink Port Signal Loss Line Excessive Error DefectLine Signal Degraded Error Uplink Port Loss of SignalConfiguring the Internal Bridge Configuring Fast Ethernet BridgeTo configure the Fast Ethernet bridge Mbps, 8 Mbps, No LimitConfiguring the Bridge Ports Configuring Ethernet Management and Data Bridge PortsTo access the Bridge Port menu To configure the Ethernet management and data bridge portsConfiguring the POS Bridge Port To configure the POS portDisplaying the RIC-155 Status Displaying the System StatusTo display the system information Displaying the Port Status Displaying the Ethernet Port StatusTo display the Ethernet port status Displaying the STM-1/OC-3c Port Status DATA/MNG Port Status ParametersTo display the STM-1/OC-3c port status Parameters ValuesChanging the Password To change the current passwordAdditional Tasks STM-1/OC-3c Port Status Parameters21. User Access Menu Displaying the RIC-155 InventoryInstalling Software Releases Installing a New Software Release via TftpTo install a new software release via Tftp Installing a New Software Release via Xmodem To install a new software release via XmodemTransferring Configuration Files To upload a configuration fileTo download a configuration file Displaying the Software VersionSwitching Software Versions Resetting RIC-155To switch software versions Resetting RIC-155 to Factory Defaults Resetting RIC-155To reset RIC-155 to the defaults To reset RIC-155Chapter Troubleshooting Diagnostics Monitoring PerformanceDisplaying the Ethernet Statistics To display the Ethernet statisticsDisplaying SDH/SONET Statistics To display the current SDH/SONET statisticsUplink Statistics Screen, Display Description RangeUasl RCV Abort To display SDH/SONET statistics for all intervals 1explains all SDH/SONET statistics parametersDetecting Errors Handling AlarmsPower-Up Self-Test Front Panel LEDsDisplaying System Alarms To display the system alarmsWorking with the Log File To display the event log fileConfiguring Alarm Severity To configure the alarm severityTo clear the event log Masking Port Alarms To mask RIC-155 alarmsRIC-155 Alarms and Warnings Terminal Message Description SeverityRIC-155 Events Number Terminal Message DescriptionTroubleshooting and Diagnostics Handling Alarms Appendix a Connector Wiring Ethernet ConnectorsAlarm Relay Connector Table A-1. ETH and MNG-ETH Connector PinoutControl Connector Table A-2. Alarm Connector PinoutTable A-3. Control Connector Pinout Pin Alarm Relay FunctionAppendix B Traffic Separation Port-Based Traffic SeparationNone MNG onlyPort-Based/VLAN-Based Traffic Separation AllLocal Mng Only Default Tagging Table B-1. Default Tagging ModesTagging Modes of the Bridge Ports Uplink and Host PortsForwarding Mode Port Filter Management Access Mode None MNG Only All Local MNG OnlyInternal Operation Modes of the Bridge Ports NoneMNG Only AllConfiguring for a Typical Application Managing RIC-155 via MNG PortLocal MNG Only Managing RIC-155 via Data Port Figure B-9. Managing RIC-155 via MNG PortFigure B-10. Managing RIC-155 via Data Port Index RADview-Lite,3-5 STM-1/OC-3c interface, 1-2,1-6Customer Response Form Excellent Good Fair Poor Very PoorPage Error Report Page Page International Headquarters