RAD Data comm RIC-155 Connecting the Power Cable, Connecting AC Power, Connecting DC Power

Page 25

RIC-155Installation and Operation Manual		Chapter 2 Installation and Setup

2.5Connecting the Power Cable

To connect RIC-155 to the power source, refer to the appropriate section below, depending on your version of the unit (AC or DC).

	Before switching on this unit and connecting or disconnecting any other cable,
	the protective earth terminals of this unit must be connected to the protective
	ground conductor of the mains (AC or DC) power cord. If you are using an
Warning	extension cord (power cable) make sure it is grounded as well.
	Any interruption of the protective (grounding) conductor (inside or outside the
	instrument) or disconnecting of the protective earth terminal can make this
	unit dangerous. Intentional interruption is prohibited.

Connecting AC Power

AC power is supplied to the RIC-155 through a standard 3-prong plug

AC power should be supplied via a 1.5m (5 ft) standard power cable terminated by a standard 3-prong socket. A cable is provided with the unit.

To connect AC power:

1.Connect the power cable to the power connector on the RIC-155 rear panel.

2.Connect the power cable to the mains outlet.

The unit will be turned on automatically upon connection to the mains.

Connecting DC Power

A special IEC 60320 adapter for -48/-60 VDC power connection is supplied with the unit. 24 VDC RIC-155 units have a terminal block DC inlet and adapter supplied with the unit.

To connect DC power:

•Refer to the DC power supply connection supplements for instructions how to wire the DC adapters, and to the Handling Energized Products section.

Connecting the Power Cable

2-3

Image 25

Contents RIC-155 Page RIC-155 Limited Warranty Please observe the following precautions General Safety InstructionsConnection of AC Mains General Safety PracticesConnection of DC Mains Connection of Data and Telecommunications Cables Ports Safety StatusElectromagnetic Compatibility EMC Conventions Canadian Emission RequirementsManufacturers Name Manufacturers Address SafetyProduct Name Supplementary InformationConfiguring RIC-155 Installing RIC-155Quick Start Guide To configure RIC-155 Configuring RIC-155Contents Appendix A. Connector Wiring Appendix B. Traffic Separation Troubleshooting and DiagnosticsOverview Chapter IntroductionVersions Application10/100BaseT Interface FeaturesSTM-1/OC-3c Interface Fiber Optic Interface OptionsManagement Alarm RelayInternal Bridge Status ReportingRIC-155 3D View Physical DescriptionFunctional Description RIC-155 Block DiagramTechnical Specifications Temperature 50C / 32-122F Humidity Up to 90%, non-condensing Alarm Types Major and minor Connector DB-9, femaleIntroduction Introduction Chapter Installation and SetupSite Requirements and Prerequisites Connecting the Interface Cables Package ContentsConnecting AC Power Connecting the Power CableConnecting DC Power Connecting the Power Cable Chapter Operation Controls and IndicatorsTurning On RIC-155 To turn on RIC-155Indicator Status RIC-155 Normal Indicator StatusRIC-155 LEDs Name Function LocationRIC-155 Default Settings Default SettingsParameter Default Value Configuration AlternativesManaging RIC-155 via Terminal Port UplinkPreparing the Terminal Managing RIC-155 via Ethernet PortsStarting Terminal Session for a First Time To prepare RIC-155 for network managementTo start a ConfiguRAD session To enter the user name and password Loging onNavigating the Management Menus Menu MapChoosing Options To choose an option ConfiguRAD sessionCorrecting Entries To choose an option terminal sessionNavigating Tables Turning Off RIC-155Logging Out Operation Turning Off RIC-155 Configuring RIC-155 for Management Chapter ConfigurationTo access the Configuration menu To access the Management menuTo enter device information Entering Device InformationTo define the IP parameters Configuring the Host ParametersTo configure the network managers Configuring the Network ManagersTo define the management access method Controlling the Management AccessTo enable or disable management ports Configuring the RIC-155 for OperationConfiguring Control Port Parameters Configuring the Clock SourceConfiguring the Security Timeout Enabling and Disabling Pop-up AlarmsChanging the Control Port Data Rate Configuring the Ethernet Interface Configuring the Physical PortsConfiguring the STM-1/OC-3c Interface 10E-5,10E-6,10E-7,10E-8,10E-9 10E-3,10E-4,10E-5J1 Path Trace Line Excessive Error Defect Uplink Port Signal LossLine Signal Degraded Error Uplink Port Loss of SignalConfiguring Fast Ethernet Bridge Configuring the Internal BridgeTo configure the Fast Ethernet bridge Mbps, 8 Mbps, No LimitConfiguring Ethernet Management and Data Bridge Ports Configuring the Bridge PortsTo access the Bridge Port menu To configure the Ethernet management and data bridge portsTo configure the POS port Configuring the POS Bridge PortDisplaying the System Status Displaying the RIC-155 StatusTo display the system information Displaying the Ethernet Port Status Displaying the Port StatusTo display the Ethernet port status DATA/MNG Port Status Parameters Displaying the STM-1/OC-3c Port StatusTo display the STM-1/OC-3c port status Parameters ValuesTo change the current password Changing the PasswordAdditional Tasks STM-1/OC-3c Port Status ParametersDisplaying the RIC-155 Inventory 21. User Access MenuInstalling a New Software Release via Tftp Installing Software ReleasesTo install a new software release via Tftp To install a new software release via Xmodem Installing a New Software Release via XmodemTo upload a configuration file Transferring Configuration FilesTo download a configuration file Displaying the Software VersionResetting RIC-155 Switching Software VersionsTo switch software versions Resetting RIC-155 Resetting RIC-155 to Factory DefaultsTo reset RIC-155 to the defaults To reset RIC-155Monitoring Performance Chapter Troubleshooting DiagnosticsDisplaying the Ethernet Statistics To display the Ethernet statisticsTo display the current SDH/SONET statistics Displaying SDH/SONET StatisticsDisplay Description Range Uplink Statistics Screen,Uasl RCV Abort 1explains all SDH/SONET statistics parameters To display SDH/SONET statistics for all intervalsHandling Alarms Detecting ErrorsPower-Up Self-Test Front Panel LEDsTo display the system alarms Displaying System AlarmsWorking with the Log File To display the event log fileTo configure the alarm severity Configuring Alarm SeverityTo clear the event log To mask RIC-155 alarms Masking Port AlarmsRIC-155 Alarms and Warnings Terminal Message Description SeverityNumber Terminal Message Description RIC-155 EventsTroubleshooting and Diagnostics Handling Alarms Ethernet Connectors Appendix a Connector WiringAlarm Relay Connector Table A-1. ETH and MNG-ETH Connector PinoutTable A-2. Alarm Connector Pinout Control ConnectorTable A-3. Control Connector Pinout Pin Alarm Relay FunctionPort-Based Traffic Separation Appendix B Traffic SeparationNone MNG onlyAll Port-Based/VLAN-Based Traffic SeparationLocal Mng Only Table B-1. Default Tagging Modes Default TaggingTagging Modes of the Bridge Ports Uplink and Host PortsManagement Access Mode None MNG Only All Local MNG Only Forwarding Mode Port FilterInternal Operation Modes of the Bridge Ports NoneAll MNG OnlyManaging RIC-155 via MNG Port Configuring for a Typical ApplicationLocal MNG Only Figure B-9. Managing RIC-155 via MNG Port Managing RIC-155 via Data PortFigure B-10. Managing RIC-155 via Data Port Index STM-1/OC-3c interface, 1-2,1-6 RADview-Lite,3-5Excellent Good Fair Poor Very Poor Customer Response FormPage Error Report Page Page International Headquarters