Sony SX-215 user manual User’s Guide Print Server Components

Page 10

User’s Guide

Print Server Components

The print server includes the following components. Detailed descriptions of these components are provided below:

Power connector – The power supply cable plugs into this connector.

Test button – Pressing this button for less than three seconds will print a test page on the printer. Pressing and holding this button for more than five seconds will reset the print server to factory default settings.

LED status indicators – used to indicate the operational states of the print server. Refer to the LED status light descriptions on the next page.

Ethernet Port – This port is used for connecting the print server to a 10/100Base-TX Ethernet card, hub, router, or other wired access point for network access.

Parallel port – The parallel port is used for connecting the print server to the IEEE 1284- compliant parallel port of your printer (parallel port models only).

USB port – The USB port is used for connecting the print server to the USB 2.0 port of your printer. You must use a standard USB A (print server side) to B (printer side) cable (USB port models only).

NOTE: A USB 2.0 cable must be used to take full advantage of the high-speed USB 2.0 connection.

Document #40181-420 Rev. B

10

Image 10

Contents SX-200/SX-215 User’s GuideUser’s Guide User’s Guide SET Port P1 Sojbusy SET IP TCP SH Smtp Introduction Package Contents Product OverviewWindows System Requirements User’s Guide About This User’s GuideOther Operating System Requirements User’s Guide Wireless Print Server Requirements User’s Guide Print Server Components LED Indicators Label Color State StatusWireless Default Settings wireless print servers only Factory Default SettingsDefault Settings wired and wireless print servers Pushbutton FunctionsHardware Installation Before You BeginUser’s Guide User’s Guide Verifying the Connection to the Printer ExtendView Utility Configuration and ManagementConfiguration Options Web Browser InterfaceHP Web JetAdmin Utility Configuration ConsoleDocument #40181-420 Rev. B User’s Guide Telnet User’s Guide Windows Print Queue Configuration Adding the Standard TCP/IP PortSelect the local printer, as shown below, and click Next User’s Guide User’s Guide Macintosh Print Queue Configuration Configuring to Print Using TCP/IP OS Printing Problems TroubleshootingIntroduction Troubleshooting Windows Problems Checking the Network Connection and CablingUser’s Guide Troubleshooting Network Configuration Problems User’s Guide Troubleshooting Wireless Configuration Problems Where to Get Help User’s Guide Returning Products Appendix a Safety and Regulatory Notices Information for United States Users SX-200User’s Guide Declaration of Conformity FCC SX-200 Information for Canadian Users IC notice SX-200User’s Guide Information for European Users SX-200 Declaration of Conformity CE SX-200User’s Guide Declaration of Conformity FCC SX-215 Information for Canadian Users IC Notice SX-215User’s Guide Appendix B Updating Firmware User’s Guide User’s Guide Loading New Firmware Macintosh OS-X Telnet Command Console Access User’s Guide Command console access informationSerial Port Command Console Access SH NW Auth Network CommandsSH NW SET NW ENCSET NW KEY# SH NW ModeSH NW ENC SET NW KeyvalSH NW Speed CL NW BSsid SH NW Certcn SH NW StatsSET NW Certcn SET NW CERTCN2SH NW Certexp SH NW CERTCN2SET NW Certexp SET NW CertkeySH NW Inap SET NW PWSET NW Inap SET NW RealmSET NW Wpatrace SH NW WpagroupSET NW Wpapsk SET NW IroamSH NW DFS SH NW IroamSET NW DFS SET NW REGDOMainSH NW REGDOMain Port CommandsSET NW Wired Sets Ethernet Speed to 10baseT, 100baseTX, or AutosenseUser’s Guide SET Port P1 BIDir User’s Guide Parallel Port CommandsEnable or disable bidirectional mode Shows Port parameters Sample outputEnable or disable PJL status initialization SET Port P1 Nbuf ENable DIsableCL Port port JOB SET SERVEr DEscription Server Information CommandsUSB Port Commands SET SERVEr NAmeSET Snmp SETCOMM2 SET Snmp SETCOMM1SH Serial SH Snmp User’s Guide SH SERVErSH SERVEr COunters SH VErsionSET Servi service name EOT Service CommandsSET Servi service name BOT SET Servi service name FIlterSET Servi service name IP SET Servi service name FMSSET Servi service name FRS SET Servi service name NAmeSET Servi service name RECeive User’s Guide SET Servi service name PRIoritySH Servi PRI servicenum SET Servi service name TCPString Commands TCP/IP CommandsSET IP ARP ENable User’s Guide SET IP ACcessSH IP ACcess SET IP RANgeSET IP FTP SET IP ChksumSET IP Http SET IP LPD SET IP TCP SET IP TftpSH IP Shows TCP/IP related Parameters Sample outputFirmware Update Shows the firmware update parameters Sample output User’s Guide SH LOAdExit Other CommandsSET Default SH FreeInit SET PoweronSH Poweron SaveNetware Commands UnprotectSET Netw REscan User’s Guide SET Netw POllingSET Netw QServer SET Netw SErverEmail Printing Commands SET Smtp ENable SET POP3 PAsswordSET POP3 TImeout SET Smtp ADdressSET DLC TIMeout DLC / Netbeui CommandsSET DLC ENable SH POP3Appletalk Commands SH DLCConfigures the Appletalk Zone for this server SET APPletalk ZOneWireless Security Configuration ExtendViewKey Selection SH NW SET NW KEY# SH NW Speed SET NW Certcn SH NW Certexp SH NW Inap SET NW Wpapsk