Sony SX-215 user manual Key Selection

Page 80

User’s Guide

∙WPA2-WPA uses CCMP for pair-wise encryption, but allows TKIP for group encryption.

Key Selection

If WEP encryption is selected, and the authentication mode is not an EAP (802.1x) mode, select the desired WEP key to be used, one through four.

WEP Key

These fields are ignored unless the encryption mode is 64 or 128 bit WEP. Enter up to 10 hexadecimal digits for 64 bit WEP, or 26 hexadecimal digits for 128 bit WEP.

Authentication Type

Choose type of authentication to be performed with the network access point, or with a peer unit in Ad- hoc mode.

User ID

Enter the logon user ID that the server uses to authenticate to the 802.1x-enabled network. The user ID and password must be in the authentication server database, and is used in TTLS, LEAP, and PEAP configurations. The default user ID is 'anonymous'. A realm defines a grouping of users. If a realm is required for your network, it is separated from the user ID by a '@' character. Realms make it easier to segregate user groups into independently administered databases, to apply policies on a user group basis, and to establish roaming agreements to name a few applications. The default realm if not specified is 'anonymous'. Realm is used with TTLS configurations, and sometimes with PEAP.

Password

Enter the logon password that the server uses to authenticate to the 802.1x enabled network. The user ID and password must be in the authentication server database, and is used in TTLS, LEAP, and PEAP configurations. The password may be a text string, or a string of hex bytes prefixed with '\x'. The default password is 'anonymous'.

Certificate Common Name

Enter the name of the certificate on the primary authentication server. If both of the

common names are set to null, all certificates are accepted. The default is null. Certificate common name is used in TTLS and PEAP configurations.

Certificate Root Key

Enter the authentication key used to verify the root certificate in the certificate chain provided by the authentication server. To set to null, leave this field blank. Certificate Root Key is used in TTLS and PEAP configurations. The Certificate Root Key can be extracted by clicking Browse and selecting the actual certificate if you don’t want to type it in manually.

Certificate Root Key Exponent

This value must match the authentication server certificate value. The default is 65537 (x10001). Certificate Root Key Exponent is used in TTLS and PEAP configurations. The Certificate Root Key Exponent can be extracted by clicking Browse and selecting the actual certificate if you don’t want to type it in manually.

Authentication Protocol

This field determines how the server authenticates itself to the 802.1x enabled network after an 802.1x session is established. The default is PAP. Sometimes referred to as inner-authentication protocol, it is used in TTLS and PEAP configurations.

Pre-Shared Key

If the PSK mode of authentication is selected with WPA (TKIP) or WPA2 (CCMP) encryption, the key value or pass-phrase entered here is used to initialize the session with the access point. If a key value is entered, it must be exactly 64 hex characters. A pass-phrase must be 8 to 63 displayable characters.

Document #40181-420 Rev. B

80

Page 79 Page 81
Image 80
Page 79 Page 81
Contents SX-200/SX-215 User’s GuideUser’s Guide User’s Guide SET Port P1 Sojbusy SET IP TCP SH Smtp Introduction Package Contents Product OverviewOther Operating System Requirements User’s Guide About This User’s GuideWindows System Requirements User’s Guide Wireless Print Server Requirements User’s Guide Print Server Components LED Indicators Label Color State StatusFactory Default Settings Default Settings wired and wireless print serversWireless Default Settings wireless print servers only Pushbutton FunctionsHardware Installation Before You BeginUser’s Guide User’s Guide Verifying the Connection to the Printer Configuration and Management Configuration OptionsExtendView Utility Web Browser InterfaceHP Web JetAdmin Utility Configuration ConsoleDocument #40181-420 Rev. B User’s Guide Telnet User’s Guide Windows Print Queue Configuration Adding the Standard TCP/IP PortSelect the local printer, as shown below, and click Next User’s Guide User’s Guide Macintosh Print Queue Configuration Configuring to Print Using TCP/IP OS Introduction TroubleshootingPrinting Problems Troubleshooting Windows Problems Checking the Network Connection and CablingUser’s Guide Troubleshooting Network Configuration Problems User’s Guide Troubleshooting Wireless Configuration Problems Where to Get Help User’s Guide Returning Products Appendix a Safety and Regulatory Notices Information for United States Users SX-200User’s Guide Declaration of Conformity FCC SX-200 Information for Canadian Users IC notice SX-200User’s Guide Information for European Users SX-200 Declaration of Conformity CE SX-200User’s Guide Declaration of Conformity FCC SX-215 Information for Canadian Users IC Notice SX-215User’s Guide Appendix B Updating Firmware User’s Guide User’s Guide Loading New Firmware Macintosh OS-X Serial Port Command Console Access User’s Guide Command console access informationTelnet Command Console Access Network Commands SH NWSH NW Auth SET NW ENCSH NW Mode SH NW ENCSET NW KEY# SET NW KeyvalSH NW Speed CL NW BSsid SH NW Stats SET NW CertcnSH NW Certcn SET NW CERTCN2SH NW CERTCN2 SET NW CertexpSH NW Certexp SET NW CertkeySET NW PW SET NW InapSH NW Inap SET NW RealmSH NW Wpagroup SET NW WpapskSET NW Wpatrace SET NW IroamSH NW Iroam SET NW DFSSH NW DFS SET NW REGDOMainPort Commands SET NW WiredSH NW REGDOMain Sets Ethernet Speed to 10baseT, 100baseTX, or AutosenseUser’s Guide User’s Guide Parallel Port Commands Enable or disable bidirectional modeSET Port P1 BIDir Shows Port parameters Sample outputCL Port port JOB SET Port P1 Nbuf ENable DIsableEnable or disable PJL status initialization Server Information Commands USB Port CommandsSET SERVEr DEscription SET SERVEr NAmeSH Serial SET Snmp SETCOMM1SET Snmp SETCOMM2 User’s Guide SH SERVEr SH SERVEr COuntersSH Snmp SH VErsionService Commands SET Servi service name BOTSET Servi service name EOT SET Servi service name FIlterSET Servi service name FMS SET Servi service name FRSSET Servi service name IP SET Servi service name NAmeUser’s Guide SET Servi service name PRIority SH Servi PRI servicenumSET Servi service name RECeive SET Servi service name TCPString Commands TCP/IP CommandsUser’s Guide SET IP ACcess SH IP ACcessSET IP ARP ENable SET IP RANgeSET IP Http SET IP ChksumSET IP FTP SET IP LPD SET IP TCP SET IP TftpSH IP Shows TCP/IP related Parameters Sample outputFirmware Update Shows the firmware update parameters Sample output User’s Guide SH LOAdOther Commands SET DefaultExit SH FreeSET Poweron SH PoweronInit SaveNetware Commands UnprotectUser’s Guide SET Netw POlling SET Netw QServerSET Netw REscan SET Netw SErverEmail Printing Commands SET POP3 PAssword SET POP3 TImeoutSET Smtp ENable SET Smtp ADdressDLC / Netbeui Commands SET DLC ENableSET DLC TIMeout SH POP3Appletalk Commands SH DLCConfigures the Appletalk Zone for this server SET APPletalk ZOneWireless Security Configuration ExtendViewKey Selection SH NW SET NW KEY# SH NW Speed SET NW Certcn SH NW Certexp SH NW Inap SET NW Wpapsk
Top Page Image Contents