Sony SX-215 user manual User’s Guide About This User’s Guide, Windows System Requirements

Page 8

User’s Guide

About This User’s Guide

This User’s Guide contains information on system requirements, basic troubleshooting, and instructions on the following:

Installing the print server hardware

Configuring the print server for use on your network

Windows print queue configuration

Macintosh print queue configuration

Windows™ System Requirements

To configure the print server settings (wired and wireless versions) using the provided ExtendView Utility in Windows, your Windows-based system should include the following components:

A PC with a 133 MHz or higher processor

Microsoft Windows operating system

At least 64 MB of RAM (memory)

At least 3 MB of free hard disk space to install the software

A CD-ROM drive (to load the software)

A PC equipped with a USB version 1.1 or 2.0 port

An Internet connection (for online product registration)

Other Operating System Requirements

Users can access the configuration settings for the Serial Server through a standard web browser by entering the IP address the serial server obtains from a DHCP server. If your network does not have DHCP service, then enter the default static IP address of the Serial Server (192.0.0.192).

Document #40181-420 Rev. B

8

Image 8

Contents SX-200/SX-215 User’s GuideUser’s Guide User’s Guide SET Port P1 Sojbusy SET IP TCP SH Smtp Introduction Package Contents Product OverviewOther Operating System Requirements User’s Guide About This User’s GuideWindows System Requirements User’s Guide Wireless Print Server Requirements User’s Guide Print Server Components LED Indicators Label Color State StatusFactory Default Settings Default Settings wired and wireless print serversWireless Default Settings wireless print servers only Pushbutton FunctionsHardware Installation Before You BeginUser’s Guide User’s Guide Verifying the Connection to the Printer Configuration and Management Configuration OptionsExtendView Utility Web Browser InterfaceHP Web JetAdmin Utility Configuration ConsoleDocument #40181-420 Rev. B User’s Guide Telnet User’s Guide Windows Print Queue Configuration Adding the Standard TCP/IP PortSelect the local printer, as shown below, and click Next User’s Guide User’s Guide Macintosh Print Queue Configuration Configuring to Print Using TCP/IP OS Introduction TroubleshootingPrinting Problems Troubleshooting Windows Problems Checking the Network Connection and CablingUser’s Guide Troubleshooting Network Configuration Problems User’s Guide Troubleshooting Wireless Configuration Problems Where to Get Help User’s Guide Returning Products Appendix a Safety and Regulatory Notices Information for United States Users SX-200User’s Guide Declaration of Conformity FCC SX-200 Information for Canadian Users IC notice SX-200User’s Guide Information for European Users SX-200 Declaration of Conformity CE SX-200User’s Guide Declaration of Conformity FCC SX-215 Information for Canadian Users IC Notice SX-215User’s Guide Appendix B Updating Firmware User’s Guide User’s Guide Loading New Firmware Macintosh OS-X Serial Port Command Console Access User’s Guide Command console access informationTelnet Command Console Access Network Commands SH NWSH NW Auth SET NW ENCSH NW Mode SH NW ENCSET NW KEY# SET NW KeyvalSH NW Speed CL NW BSsid SH NW Stats SET NW CertcnSH NW Certcn SET NW CERTCN2SH NW CERTCN2 SET NW CertexpSH NW Certexp SET NW CertkeySET NW PW SET NW InapSH NW Inap SET NW RealmSH NW Wpagroup SET NW WpapskSET NW Wpatrace SET NW IroamSH NW Iroam SET NW DFSSH NW DFS SET NW REGDOMainPort Commands SET NW WiredSH NW REGDOMain Sets Ethernet Speed to 10baseT, 100baseTX, or AutosenseUser’s Guide User’s Guide Parallel Port Commands Enable or disable bidirectional modeSET Port P1 BIDir Shows Port parameters Sample outputCL Port port JOB SET Port P1 Nbuf ENable DIsableEnable or disable PJL status initialization Server Information Commands USB Port CommandsSET SERVEr DEscription SET SERVEr NAmeSH Serial SET Snmp SETCOMM1SET Snmp SETCOMM2 User’s Guide SH SERVEr SH SERVEr COuntersSH Snmp SH VErsionService Commands SET Servi service name BOTSET Servi service name EOT SET Servi service name FIlterSET Servi service name FMS SET Servi service name FRSSET Servi service name IP SET Servi service name NAmeUser’s Guide SET Servi service name PRIority SH Servi PRI servicenumSET Servi service name RECeive SET Servi service name TCPString Commands TCP/IP CommandsUser’s Guide SET IP ACcess SH IP ACcessSET IP ARP ENable SET IP RANgeSET IP Http SET IP ChksumSET IP FTP SET IP LPD SET IP TCP SET IP TftpSH IP Shows TCP/IP related Parameters Sample outputFirmware Update Shows the firmware update parameters Sample output User’s Guide SH LOAdOther Commands SET DefaultExit SH FreeSET Poweron SH PoweronInit SaveNetware Commands UnprotectUser’s Guide SET Netw POlling SET Netw QServerSET Netw REscan SET Netw SErverEmail Printing Commands SET POP3 PAssword SET POP3 TImeoutSET Smtp ENable SET Smtp ADdressDLC / Netbeui Commands SET DLC ENableSET DLC TIMeout SH POP3Appletalk Commands SH DLCConfigures the Appletalk Zone for this server SET APPletalk ZOneWireless Security Configuration ExtendViewKey Selection SH NW SET NW KEY# SH NW Speed SET NW Certcn SH NW Certexp SH NW Inap SET NW Wpapsk