Sony SX-215 user manual User’s Guide

Page 14

User’s Guide

3.Connect the print server to your printer(s) using the USB and/or parallel port of your printer. For a USB connection, use a standard USB A (print server side) to B (printer side) cable. For a parallel connection, use an IEEE 1284-compliant parallel printer cable.

4.Plug the print server power supply adapter into a suitable AC receptacle, and then plug the power supply cable into the print server. The print server will run through a sequence of power-up diagnostics for a few seconds.

If the print server is operating properly, the power LED will illuminate continuously (refer to page 1-5 for detailed LED status descriptions).

If the power LED blinks continuously in a regular pattern, a problem exists. If this is the case, try powering the print server OFF and then ON again.

If the problem persists, refer to the Troubleshooting section in this User’s Guide.

5.Connect the print server to your network through a switch or hub using a category 5 (CAT5) Ethernet cable. The print server’s IP address must be configured before a network connection is available. If your network offers DHCP (Dynamic Host Configuration Protocol), the print server will automatically search for a DCHP server upon power up and obtain an IP address. If your network does not offer DHCP, a static (fixed) IP address must be assigned (see your system administrator for assistance). In most cases, a fixed IP address is preferred because a DHCP server may not always assign the same IP address to the print server when the print server is powered ON.

NOTE: The IP address must be within a valid range, unique to your network, and in the same subnet as your PC.

NOTE: For wireless print servers, if a wired connection is established to the unit, the wireless link will be disabled.

Document #40181-420 Rev. B

14

Image 14

Contents SX-200/SX-215 User’s GuideUser’s Guide User’s Guide SET Port P1 Sojbusy SET IP TCP SH Smtp Introduction Package Contents Product OverviewOther Operating System Requirements User’s Guide About This User’s GuideWindows System Requirements User’s Guide Wireless Print Server Requirements User’s Guide Print Server Components LED Indicators Label Color State StatusWireless Default Settings wireless print servers only Factory Default SettingsDefault Settings wired and wireless print servers Pushbutton FunctionsHardware Installation Before You BeginUser’s Guide User’s Guide Verifying the Connection to the Printer ExtendView Utility Configuration and ManagementConfiguration Options Web Browser InterfaceHP Web JetAdmin Utility Configuration ConsoleDocument #40181-420 Rev. B User’s Guide Telnet User’s Guide Windows Print Queue Configuration Adding the Standard TCP/IP PortSelect the local printer, as shown below, and click Next User’s Guide User’s Guide Macintosh Print Queue Configuration Configuring to Print Using TCP/IP OS Introduction TroubleshootingPrinting Problems Troubleshooting Windows Problems Checking the Network Connection and CablingUser’s Guide Troubleshooting Network Configuration Problems User’s Guide Troubleshooting Wireless Configuration Problems Where to Get Help User’s Guide Returning Products Appendix a Safety and Regulatory Notices Information for United States Users SX-200User’s Guide Declaration of Conformity FCC SX-200 Information for Canadian Users IC notice SX-200User’s Guide Information for European Users SX-200 Declaration of Conformity CE SX-200User’s Guide Declaration of Conformity FCC SX-215 Information for Canadian Users IC Notice SX-215User’s Guide Appendix B Updating Firmware User’s Guide User’s Guide Loading New Firmware Macintosh OS-X Serial Port Command Console Access User’s Guide Command console access informationTelnet Command Console Access SH NW Auth Network CommandsSH NW SET NW ENCSET NW KEY# SH NW ModeSH NW ENC SET NW KeyvalSH NW Speed CL NW BSsid SH NW Certcn SH NW StatsSET NW Certcn SET NW CERTCN2SH NW Certexp SH NW CERTCN2SET NW Certexp SET NW CertkeySH NW Inap SET NW PWSET NW Inap SET NW RealmSET NW Wpatrace SH NW WpagroupSET NW Wpapsk SET NW IroamSH NW DFS SH NW IroamSET NW DFS SET NW REGDOMainSH NW REGDOMain Port CommandsSET NW Wired Sets Ethernet Speed to 10baseT, 100baseTX, or AutosenseUser’s Guide SET Port P1 BIDir User’s Guide Parallel Port CommandsEnable or disable bidirectional mode Shows Port parameters Sample outputCL Port port JOB SET Port P1 Nbuf ENable DIsableEnable or disable PJL status initialization SET SERVEr DEscription Server Information CommandsUSB Port Commands SET SERVEr NAmeSH Serial SET Snmp SETCOMM1SET Snmp SETCOMM2 SH Snmp User’s Guide SH SERVErSH SERVEr COunters SH VErsionSET Servi service name EOT Service CommandsSET Servi service name BOT SET Servi service name FIlterSET Servi service name IP SET Servi service name FMSSET Servi service name FRS SET Servi service name NAmeSET Servi service name RECeive User’s Guide SET Servi service name PRIoritySH Servi PRI servicenum SET Servi service name TCPString Commands TCP/IP CommandsSET IP ARP ENable User’s Guide SET IP ACcessSH IP ACcess SET IP RANgeSET IP Http SET IP ChksumSET IP FTP SET IP LPD SET IP TCP SET IP TftpSH IP Shows TCP/IP related Parameters Sample outputFirmware Update Shows the firmware update parameters Sample output User’s Guide SH LOAdExit Other CommandsSET Default SH FreeInit SET PoweronSH Poweron SaveNetware Commands UnprotectSET Netw REscan User’s Guide SET Netw POllingSET Netw QServer SET Netw SErverEmail Printing Commands SET Smtp ENable SET POP3 PAsswordSET POP3 TImeout SET Smtp ADdressSET DLC TIMeout DLC / Netbeui CommandsSET DLC ENable SH POP3Appletalk Commands SH DLCConfigures the Appletalk Zone for this server SET APPletalk ZOneWireless Security Configuration ExtendViewKey Selection SH NW SET NW KEY# SH NW Speed SET NW Certcn SH NW Certexp SH NW Inap SET NW Wpapsk