Sony SX-215 user manual Hardware Installation, Before You Begin

Page 13

User’s Guide

Section 2 – Hardware Installation

Before You Begin

Before installing the print server, make sure you have installed and set up your printer as described in the documentation that came with the printer and that your printer functions properly. SX-200 Series Print Servers support a parallel and/or USB connection to your printer.

Hardware Installation (wired and wireless versions)

NOTE: Be sure to review the hardware requirements in the previous section to ensure you have the necessary information before installing the print server.

1.Write down the 12-digit MAC address printed on the label located on the bottom of the print server (for example: 004017023F96). You may need this number in order to configure the print server.

2.Mount the print server on either the printer or the desktop:

 Printer mount – attach the print server to a suitable location on the side or rear of your printer by applying an adhesive Velcro strip (provided in the printer mounting kit) to your printer and at the top of the print server as it is to be attached to your printer.

Desktop mount – attach the adhesive rubber feet (provided in the desktop mounting kit) to the bottom of the print server as shown below.

Document #40181-420 Rev. B

13

Image 13

Contents User’s Guide SX-200/SX-215User’s Guide User’s Guide SET Port P1 Sojbusy SET IP TCP SH Smtp Product Overview Introduction Package ContentsWindows System Requirements User’s Guide About This User’s GuideOther Operating System Requirements User’s Guide Wireless Print Server Requirements User’s Guide Print Server Components Label Color State Status LED IndicatorsDefault Settings wired and wireless print servers Factory Default SettingsWireless Default Settings wireless print servers only Pushbutton FunctionsBefore You Begin Hardware InstallationUser’s Guide User’s Guide Verifying the Connection to the Printer Configuration Options Configuration and ManagementExtendView Utility Web Browser InterfaceConfiguration Console HP Web JetAdmin UtilityDocument #40181-420 Rev. B User’s Guide Telnet Adding the Standard TCP/IP Port User’s Guide Windows Print Queue ConfigurationSelect the local printer, as shown below, and click Next User’s Guide User’s Guide Macintosh Print Queue Configuration Configuring to Print Using TCP/IP OS Printing Problems TroubleshootingIntroduction Checking the Network Connection and Cabling Troubleshooting Windows ProblemsUser’s Guide Troubleshooting Network Configuration Problems User’s Guide Troubleshooting Wireless Configuration Problems Where to Get Help User’s Guide Returning Products Information for United States Users SX-200 Appendix a Safety and Regulatory NoticesInformation for Canadian Users IC notice SX-200 User’s Guide Declaration of Conformity FCC SX-200Declaration of Conformity CE SX-200 User’s Guide Information for European Users SX-200Information for Canadian Users IC Notice SX-215 User’s Guide Declaration of Conformity FCC SX-215User’s Guide Appendix B Updating Firmware User’s Guide User’s Guide Loading New Firmware Macintosh OS-X Telnet Command Console Access User’s Guide Command console access informationSerial Port Command Console Access SH NW Network CommandsSH NW Auth SET NW ENCSH NW ENC SH NW ModeSET NW KEY# SET NW KeyvalSH NW Speed CL NW BSsid SET NW Certcn SH NW StatsSH NW Certcn SET NW CERTCN2SET NW Certexp SH NW CERTCN2SH NW Certexp SET NW CertkeySET NW Inap SET NW PWSH NW Inap SET NW RealmSET NW Wpapsk SH NW WpagroupSET NW Wpatrace SET NW IroamSET NW DFS SH NW IroamSH NW DFS SET NW REGDOMainSET NW Wired Port CommandsSH NW REGDOMain Sets Ethernet Speed to 10baseT, 100baseTX, or AutosenseUser’s Guide Enable or disable bidirectional mode User’s Guide Parallel Port CommandsSET Port P1 BIDir Shows Port parameters Sample outputEnable or disable PJL status initialization SET Port P1 Nbuf ENable DIsableCL Port port JOB USB Port Commands Server Information CommandsSET SERVEr DEscription SET SERVEr NAmeSET Snmp SETCOMM2 SET Snmp SETCOMM1SH Serial SH SERVEr COunters User’s Guide SH SERVErSH Snmp SH VErsionSET Servi service name BOT Service CommandsSET Servi service name EOT SET Servi service name FIlterSET Servi service name FRS SET Servi service name FMSSET Servi service name IP SET Servi service name NAmeSH Servi PRI servicenum User’s Guide SET Servi service name PRIoritySET Servi service name RECeive SET Servi service name TCPTCP/IP Commands String CommandsSH IP ACcess User’s Guide SET IP ACcessSET IP ARP ENable SET IP RANgeSET IP FTP SET IP ChksumSET IP Http SET IP LPD SET IP Tftp SET IP TCPShows TCP/IP related Parameters Sample output SH IPFirmware Update User’s Guide SH LOAd Shows the firmware update parameters Sample outputSET Default Other CommandsExit SH FreeSH Poweron SET PoweronInit SaveUnprotect Netware CommandsSET Netw QServer User’s Guide SET Netw POllingSET Netw REscan SET Netw SErverEmail Printing Commands SET POP3 TImeout SET POP3 PAsswordSET Smtp ENable SET Smtp ADdressSET DLC ENable DLC / Netbeui CommandsSET DLC TIMeout SH POP3SH DLC Appletalk CommandsSET APPletalk ZOne Configures the Appletalk Zone for this serverExtendView Wireless Security ConfigurationKey Selection SH NW SET NW KEY# SH NW Speed SET NW Certcn SH NW Certexp SH NW Inap SET NW Wpapsk