Sony SX-215 Appendix a Safety and Regulatory Notices, Information for United States Users SX-200

Page 33

User’s Guide

Appendix A – Safety and Regulatory Notices

Information for United States Users: SX-200

This equipment has been tested and found to comply within the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio and television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver,

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

The user is cautioned that changes and modifications made to the equipment without the approval of manufacturer could void the user’s authority to operate this equipment.

Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

The radiated output power of the print server is far below the FCC radio frequency exposure limits. Nevertheless, print server shall be used in such a manner that the potential for human contact during normal operation is minimized.

To satisfy RF exposure requirements, this device and its antenna(s) must operate with a separation distance of at least 20 centimeters from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users must be provided with specific operating instructions for satisfying RF exposure compliance.

Document #40181-420 Rev. B

33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents User’s Guide SX-200/SX-215User’s Guide User’s Guide SET Port P1 Sojbusy SET IP TCP SH Smtp Product Overview Introduction Package ContentsUser’s Guide About This User’s Guide Windows System RequirementsOther Operating System Requirements User’s Guide Wireless Print Server Requirements User’s Guide Print Server Components Label Color State Status LED IndicatorsDefault Settings wired and wireless print servers Factory Default SettingsWireless Default Settings wireless print servers only Pushbutton FunctionsBefore You Begin Hardware InstallationUser’s Guide User’s Guide Verifying the Connection to the Printer Configuration Options Configuration and ManagementExtendView Utility Web Browser InterfaceConfiguration Console HP Web JetAdmin UtilityDocument #40181-420 Rev. B User’s Guide Telnet Adding the Standard TCP/IP Port User’s Guide Windows Print Queue ConfigurationSelect the local printer, as shown below, and click Next User’s Guide User’s Guide Macintosh Print Queue Configuration Configuring to Print Using TCP/IP OS Troubleshooting Printing ProblemsIntroduction Checking the Network Connection and Cabling Troubleshooting Windows ProblemsUser’s Guide Troubleshooting Network Configuration Problems User’s Guide Troubleshooting Wireless Configuration Problems Where to Get Help User’s Guide Returning Products Information for United States Users SX-200 Appendix a Safety and Regulatory NoticesInformation for Canadian Users IC notice SX-200 User’s Guide Declaration of Conformity FCC SX-200Declaration of Conformity CE SX-200 User’s Guide Information for European Users SX-200Information for Canadian Users IC Notice SX-215 User’s Guide Declaration of Conformity FCC SX-215User’s Guide Appendix B Updating Firmware User’s Guide User’s Guide Loading New Firmware Macintosh OS-X User’s Guide Command console access information Telnet Command Console AccessSerial Port Command Console Access SH NW Network CommandsSH NW Auth SET NW ENCSH NW ENC SH NW ModeSET NW KEY# SET NW KeyvalSH NW Speed CL NW BSsid SET NW Certcn SH NW StatsSH NW Certcn SET NW CERTCN2SET NW Certexp SH NW CERTCN2SH NW Certexp SET NW CertkeySET NW Inap SET NW PWSH NW Inap SET NW RealmSET NW Wpapsk SH NW WpagroupSET NW Wpatrace SET NW IroamSET NW DFS SH NW IroamSH NW DFS SET NW REGDOMainSET NW Wired Port CommandsSH NW REGDOMain Sets Ethernet Speed to 10baseT, 100baseTX, or AutosenseUser’s Guide Enable or disable bidirectional mode User’s Guide Parallel Port CommandsSET Port P1 BIDir Shows Port parameters Sample outputSET Port P1 Nbuf ENable DIsable Enable or disable PJL status initializationCL Port port JOB USB Port Commands Server Information CommandsSET SERVEr DEscription SET SERVEr NAmeSET Snmp SETCOMM1 SET Snmp SETCOMM2SH Serial SH SERVEr COunters User’s Guide SH SERVErSH Snmp SH VErsionSET Servi service name BOT Service CommandsSET Servi service name EOT SET Servi service name FIlterSET Servi service name FRS SET Servi service name FMSSET Servi service name IP SET Servi service name NAmeSH Servi PRI servicenum User’s Guide SET Servi service name PRIoritySET Servi service name RECeive SET Servi service name TCPTCP/IP Commands String CommandsSH IP ACcess User’s Guide SET IP ACcessSET IP ARP ENable SET IP RANgeSET IP Chksum SET IP FTPSET IP Http SET IP LPD SET IP Tftp SET IP TCPShows TCP/IP related Parameters Sample output SH IPFirmware Update User’s Guide SH LOAd Shows the firmware update parameters Sample outputSET Default Other CommandsExit SH FreeSH Poweron SET PoweronInit SaveUnprotect Netware CommandsSET Netw QServer User’s Guide SET Netw POllingSET Netw REscan SET Netw SErverEmail Printing Commands SET POP3 TImeout SET POP3 PAsswordSET Smtp ENable SET Smtp ADdressSET DLC ENable DLC / Netbeui CommandsSET DLC TIMeout SH POP3SH DLC Appletalk CommandsSET APPletalk ZOne Configures the Appletalk Zone for this serverExtendView Wireless Security ConfigurationKey Selection SH NW SET NW KEY# SH NW Speed SET NW Certcn SH NW Certexp SH NW Inap SET NW Wpapsk
Top Page Image Contents