Sony SX-215 user manual Telnet

Page 20

User’s Guide

USING A THE INTERNAL COMMAND CONSOLE TO CONFIGURE THE PRINT SERVER:

The command console can be accessed using a Telnet connection via an Ethernet connection. To use a Telnet connection, follow these steps:

1.Ensure the print server is connected via an Ethernet cable to the host computer.

2.From the Windows Start menu, click on Run, and then type the following command (where x.x.x.x. is the IP address of the print server.

telnet X.X.X.X

After a connection is established, press RETURN or ENTER to get the ‘#’ prompt, enter the password ACCESS (it will not ‘echo’ on your screen), and type anything in response to the Enter Username> prompt. When you get the Local> prompt, you are ready to enter commands. Type Help for a list of console commands.

First-Time Configuration of the Wireless Print Server Using 802.11b or

802.11g (SX-215 wireless print server only)

It is recommended that you initially configure the print server via a wired connection. However, if you choose to configure the wireless print server for the first time from a computer via an 802.11b or 802.11g wireless connection, you will need to temporarily change the settings on your computer to match the default settings of the print server as follows:

Wireless Mode: Ad-Hoc(sometimes referred to as Peer-to-Peer)

Channel: 11

SSID (or wireless network name): printer

NOTE: It is not necessary to change your computer’s settings if you are configuring the print server’s settings via an Ethernet connection.

You should now be able to configure your print server using either the ExtendView Utility or the Web Browser Configuration as described in the previous sections. For wireless security configuration, see

NOTE: Be sure to set your PC back to its original wireless settings after you finish configuring the wireless print server.

Document #40181-420 Rev. B

20

Image 20

Contents SX-200/SX-215 User’s GuideUser’s Guide User’s Guide SET Port P1 Sojbusy SET IP TCP SH Smtp Introduction Package Contents Product OverviewOther Operating System Requirements User’s Guide About This User’s GuideWindows System Requirements User’s Guide Wireless Print Server Requirements User’s Guide Print Server Components LED Indicators Label Color State StatusFactory Default Settings Default Settings wired and wireless print serversWireless Default Settings wireless print servers only Pushbutton FunctionsHardware Installation Before You BeginUser’s Guide User’s Guide Verifying the Connection to the Printer Configuration and Management Configuration OptionsExtendView Utility Web Browser InterfaceHP Web JetAdmin Utility Configuration ConsoleDocument #40181-420 Rev. B User’s Guide Telnet User’s Guide Windows Print Queue Configuration Adding the Standard TCP/IP PortSelect the local printer, as shown below, and click Next User’s Guide User’s Guide Macintosh Print Queue Configuration Configuring to Print Using TCP/IP OS Introduction TroubleshootingPrinting Problems Troubleshooting Windows Problems Checking the Network Connection and CablingUser’s Guide Troubleshooting Network Configuration Problems User’s Guide Troubleshooting Wireless Configuration Problems Where to Get Help User’s Guide Returning Products Appendix a Safety and Regulatory Notices Information for United States Users SX-200User’s Guide Declaration of Conformity FCC SX-200 Information for Canadian Users IC notice SX-200User’s Guide Information for European Users SX-200 Declaration of Conformity CE SX-200User’s Guide Declaration of Conformity FCC SX-215 Information for Canadian Users IC Notice SX-215User’s Guide Appendix B Updating Firmware User’s Guide User’s Guide Loading New Firmware Macintosh OS-X Serial Port Command Console Access User’s Guide Command console access informationTelnet Command Console Access Network Commands SH NWSH NW Auth SET NW ENCSH NW Mode SH NW ENCSET NW KEY# SET NW KeyvalSH NW Speed CL NW BSsid SH NW Stats SET NW CertcnSH NW Certcn SET NW CERTCN2SH NW CERTCN2 SET NW CertexpSH NW Certexp SET NW CertkeySET NW PW SET NW InapSH NW Inap SET NW RealmSH NW Wpagroup SET NW WpapskSET NW Wpatrace SET NW IroamSH NW Iroam SET NW DFSSH NW DFS SET NW REGDOMainPort Commands SET NW WiredSH NW REGDOMain Sets Ethernet Speed to 10baseT, 100baseTX, or AutosenseUser’s Guide User’s Guide Parallel Port Commands Enable or disable bidirectional modeSET Port P1 BIDir Shows Port parameters Sample outputCL Port port JOB SET Port P1 Nbuf ENable DIsableEnable or disable PJL status initialization Server Information Commands USB Port CommandsSET SERVEr DEscription SET SERVEr NAmeSH Serial SET Snmp SETCOMM1SET Snmp SETCOMM2 User’s Guide SH SERVEr SH SERVEr COuntersSH Snmp SH VErsionService Commands SET Servi service name BOTSET Servi service name EOT SET Servi service name FIlterSET Servi service name FMS SET Servi service name FRSSET Servi service name IP SET Servi service name NAmeUser’s Guide SET Servi service name PRIority SH Servi PRI servicenumSET Servi service name RECeive SET Servi service name TCPString Commands TCP/IP CommandsUser’s Guide SET IP ACcess SH IP ACcessSET IP ARP ENable SET IP RANgeSET IP Http SET IP ChksumSET IP FTP SET IP LPD SET IP TCP SET IP TftpSH IP Shows TCP/IP related Parameters Sample outputFirmware Update Shows the firmware update parameters Sample output User’s Guide SH LOAdOther Commands SET DefaultExit SH FreeSET Poweron SH PoweronInit SaveNetware Commands UnprotectUser’s Guide SET Netw POlling SET Netw QServerSET Netw REscan SET Netw SErverEmail Printing Commands SET POP3 PAssword SET POP3 TImeoutSET Smtp ENable SET Smtp ADdressDLC / Netbeui Commands SET DLC ENableSET DLC TIMeout SH POP3Appletalk Commands SH DLCConfigures the Appletalk Zone for this server SET APPletalk ZOneWireless Security Configuration ExtendViewKey Selection SH NW SET NW KEY# SH NW Speed SET NW Certcn SH NW Certexp SH NW Inap SET NW Wpapsk