Sony SX-215 user manual User’s Guide

Page 19

User’s Guide

USING THE WEB BROWSER INTERFACE TO CONFIGURE THE PRINT SERVER (NON-WINDOWS SYSTEMS):

To configure the print server using non-Windows operating systems (e.g., Unix systems), a standard web browser (e.g., Microsoft Internet Explorer or Netscape Navigator) can be used to access the print server’s embedded Web (HTTP) server pages, which contain the print server’s configuration options. No additional software is required.

1.Ensure your PC is connected and has access to your network.

2.Connect an available Ethernet cable from your network hub to the print server. Ensure the print server is powered ON.

3.With your printer and print server switched on and ready, press the test button on the print server to print a test page. The test page will display the current IP address assigned to the print server by your network DHCP service. If your network does not use DHCP, then the print server will have the default IP address of 192.0.0.192. In any case, your computer must use an IP address other than the one used by the print server in order to establish a connection between the two devices.

4.Configure the 802.11b or 802.11g wireless settings (SX-215 wireless print server only). To operate on a wireless network, you must select your country or region from the drop-down list. This field designates the region of operation for which the wireless interface is intended. It may not be legal to operate the print server in a country/region other than the country/region shown in the drop- down list. You must also set the wireless mode (ad-hoc or infrastructure), SSID channel, and WEP encryption of the wireless print server to the same configuration as the wireless network you want the print server to communicate on. All nodes of a wireless network need to have the same settings in order to communicate with each other.

5.From the host computer, open a standard web browser (e.g., Microsoft Internet Explorer or Netscape Navigator), enter the IP address of the print server into the address bar of the web browser, and then press Enter. The Web Browser Utility will be displayed, allowing you to configure the print server. The menu selections are displayed on the left side of the screen, and the individual settings are located at the top of the screen. Use the browser’s Forward and Back buttons to navigate to the sub pages where you can configure the print server’s settings.

NOTE: It may not be legal to operate the print server in a country or region other than the country or region shown in the drop-down list in ExtendView. If your country or region is not listed, check with your local government agency.

Document #40181-420 Rev. B

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents User’s Guide SX-200/SX-215User’s Guide User’s Guide SET Port P1 Sojbusy SET IP TCP SH Smtp Product Overview Introduction Package ContentsWindows System Requirements User’s Guide About This User’s GuideOther Operating System Requirements User’s Guide Wireless Print Server Requirements User’s Guide Print Server Components Label Color State Status LED IndicatorsPushbutton Functions Factory Default SettingsDefault Settings wired and wireless print servers Wireless Default Settings wireless print servers onlyBefore You Begin Hardware InstallationUser’s Guide User’s Guide Verifying the Connection to the Printer Web Browser Interface Configuration and ManagementConfiguration Options ExtendView UtilityConfiguration Console HP Web JetAdmin UtilityDocument #40181-420 Rev. B User’s Guide Telnet Adding the Standard TCP/IP Port User’s Guide Windows Print Queue ConfigurationSelect the local printer, as shown below, and click Next User’s Guide User’s Guide Macintosh Print Queue Configuration Configuring to Print Using TCP/IP OS Printing Problems TroubleshootingIntroduction Checking the Network Connection and Cabling Troubleshooting Windows ProblemsUser’s Guide Troubleshooting Network Configuration Problems User’s Guide Troubleshooting Wireless Configuration Problems Where to Get Help User’s Guide Returning Products Information for United States Users SX-200 Appendix a Safety and Regulatory NoticesInformation for Canadian Users IC notice SX-200 User’s Guide Declaration of Conformity FCC SX-200Declaration of Conformity CE SX-200 User’s Guide Information for European Users SX-200Information for Canadian Users IC Notice SX-215 User’s Guide Declaration of Conformity FCC SX-215User’s Guide Appendix B Updating Firmware User’s Guide User’s Guide Loading New Firmware Macintosh OS-X Telnet Command Console Access User’s Guide Command console access informationSerial Port Command Console Access SET NW ENC Network CommandsSH NW SH NW AuthSET NW Keyval SH NW ModeSH NW ENC SET NW KEY#SH NW Speed CL NW BSsid SET NW CERTCN2 SH NW StatsSET NW Certcn SH NW CertcnSET NW Certkey SH NW CERTCN2SET NW Certexp SH NW CertexpSET NW Realm SET NW PWSET NW Inap SH NW InapSET NW Iroam SH NW WpagroupSET NW Wpapsk SET NW WpatraceSET NW REGDOMain SH NW IroamSET NW DFS SH NW DFSSets Ethernet Speed to 10baseT, 100baseTX, or Autosense Port CommandsSET NW Wired SH NW REGDOMainUser’s Guide Shows Port parameters Sample output User’s Guide Parallel Port CommandsEnable or disable bidirectional mode SET Port P1 BIDirEnable or disable PJL status initialization SET Port P1 Nbuf ENable DIsableCL Port port JOB SET SERVEr NAme Server Information CommandsUSB Port Commands SET SERVEr DEscriptionSET Snmp SETCOMM2 SET Snmp SETCOMM1SH Serial SH VErsion User’s Guide SH SERVErSH SERVEr COunters SH SnmpSET Servi service name FIlter Service CommandsSET Servi service name BOT SET Servi service name EOTSET Servi service name NAme SET Servi service name FMSSET Servi service name FRS SET Servi service name IPSET Servi service name TCP User’s Guide SET Servi service name PRIoritySH Servi PRI servicenum SET Servi service name RECeiveTCP/IP Commands String CommandsSET IP RANge User’s Guide SET IP ACcessSH IP ACcess SET IP ARP ENableSET IP FTP SET IP ChksumSET IP Http SET IP LPD SET IP Tftp SET IP TCPShows TCP/IP related Parameters Sample output SH IPFirmware Update User’s Guide SH LOAd Shows the firmware update parameters Sample outputSH Free Other CommandsSET Default ExitSave SET PoweronSH Poweron InitUnprotect Netware CommandsSET Netw SErver User’s Guide SET Netw POllingSET Netw QServer SET Netw REscanEmail Printing Commands SET Smtp ADdress SET POP3 PAsswordSET POP3 TImeout SET Smtp ENableSH POP3 DLC / Netbeui CommandsSET DLC ENable SET DLC TIMeoutSH DLC Appletalk CommandsSET APPletalk ZOne Configures the Appletalk Zone for this serverExtendView Wireless Security ConfigurationKey Selection SH NW SET NW KEY# SH NW Speed SET NW Certcn SH NW Certexp SH NW Inap SET NW Wpapsk
Top Page Image Contents