Sony SX-215 user manual Configuration and Management, Configuration Options, ExtendView Utility

Page 16

User’s Guide

Section 3 – Configuration and Management

Configuration Options

SX-200 Series Print Servers (wired and wireless models) can be configured using a variety of options, some of which do not require any software installation on the host PC. The print server can be configured and managed via an Ethernet or wireless connection using the ExtendView Utility (recommended), the embedded web (HTTP) server pages, or the print server’s internal configuration console, which can be accessed via a Telnet connection. If you choose to use the silex ExtendView Utility (provided on the Print Server Installation CD), the software must be installed prior to use. Additional options for print server configuration and management are available as third-party utilities that can be downloaded from their respective web sites. If you are using a wireless print server, you can still configure it via an Ethernet connection or optionally configure it via a wireless connection.

ExtendView Utility

used for advanced print server configuration, and allows you to configure for TCP/IP, Netware, AppleTalk, and the wireless settings (for wireless print server models only).

uses a 32-bit graphical user interface.

works with Windows PCs running the TCP/IP protocol.

included on the Print Server installation CD.

can be downloaded from the silex web sites:

USA: http://www.silexamerica.com

after installation, this utility can be run from the START menu.

INSTALLING THE EXTENDVIEW UTILITY (WINDOWS OPERATING SYSTEMS):

1.Ensure your PC is connected and has access to your network.

2.Connect an available Ethernet cable from your network hub to the print server. Ensure the print server is powered on.

3.Insert the CD supplied with your print server into the CD-ROM drive of your computer. The CD should automatically start and display a menu screen. Click on Install Software.

4.Select ExtendView, and then click on Install.

Web Browser Interface

allows you to configure the print server with a standard web browser (e.g., Internet Explorer or Mozilla).

no additional software is needed on the system.

can be used on any system that supports web browser capabilities.

type the IP address into your web browser address bar to connect.

the default password is ACCESS (all uppercase characters).

Document #40181-420 Rev. B

16

Image 16

Contents SX-200/SX-215 User’s GuideUser’s Guide User’s Guide SET Port P1 Sojbusy SET IP TCP SH Smtp Introduction Package Contents Product OverviewWindows System Requirements User’s Guide About This User’s GuideOther Operating System Requirements User’s Guide Wireless Print Server Requirements User’s Guide Print Server Components LED Indicators Label Color State StatusFactory Default Settings Default Settings wired and wireless print serversWireless Default Settings wireless print servers only Pushbutton FunctionsHardware Installation Before You BeginUser’s Guide User’s Guide Verifying the Connection to the Printer Configuration and Management Configuration OptionsExtendView Utility Web Browser InterfaceHP Web JetAdmin Utility Configuration ConsoleDocument #40181-420 Rev. B User’s Guide Telnet User’s Guide Windows Print Queue Configuration Adding the Standard TCP/IP PortSelect the local printer, as shown below, and click Next User’s Guide User’s Guide Macintosh Print Queue Configuration Configuring to Print Using TCP/IP OS Printing Problems TroubleshootingIntroduction Troubleshooting Windows Problems Checking the Network Connection and CablingUser’s Guide Troubleshooting Network Configuration Problems User’s Guide Troubleshooting Wireless Configuration Problems Where to Get Help User’s Guide Returning Products Appendix a Safety and Regulatory Notices Information for United States Users SX-200User’s Guide Declaration of Conformity FCC SX-200 Information for Canadian Users IC notice SX-200User’s Guide Information for European Users SX-200 Declaration of Conformity CE SX-200User’s Guide Declaration of Conformity FCC SX-215 Information for Canadian Users IC Notice SX-215User’s Guide Appendix B Updating Firmware User’s Guide User’s Guide Loading New Firmware Macintosh OS-X Telnet Command Console Access User’s Guide Command console access informationSerial Port Command Console Access Network Commands SH NWSH NW Auth SET NW ENCSH NW Mode SH NW ENCSET NW KEY# SET NW KeyvalSH NW Speed CL NW BSsid SH NW Stats SET NW CertcnSH NW Certcn SET NW CERTCN2SH NW CERTCN2 SET NW CertexpSH NW Certexp SET NW CertkeySET NW PW SET NW InapSH NW Inap SET NW RealmSH NW Wpagroup SET NW WpapskSET NW Wpatrace SET NW IroamSH NW Iroam SET NW DFSSH NW DFS SET NW REGDOMainPort Commands SET NW WiredSH NW REGDOMain Sets Ethernet Speed to 10baseT, 100baseTX, or AutosenseUser’s Guide User’s Guide Parallel Port Commands Enable or disable bidirectional modeSET Port P1 BIDir Shows Port parameters Sample outputEnable or disable PJL status initialization SET Port P1 Nbuf ENable DIsableCL Port port JOB Server Information Commands USB Port CommandsSET SERVEr DEscription SET SERVEr NAmeSET Snmp SETCOMM2 SET Snmp SETCOMM1SH Serial User’s Guide SH SERVEr SH SERVEr COuntersSH Snmp SH VErsionService Commands SET Servi service name BOTSET Servi service name EOT SET Servi service name FIlterSET Servi service name FMS SET Servi service name FRSSET Servi service name IP SET Servi service name NAmeUser’s Guide SET Servi service name PRIority SH Servi PRI servicenumSET Servi service name RECeive SET Servi service name TCPString Commands TCP/IP CommandsUser’s Guide SET IP ACcess SH IP ACcessSET IP ARP ENable SET IP RANgeSET IP FTP SET IP ChksumSET IP Http SET IP LPD SET IP TCP SET IP TftpSH IP Shows TCP/IP related Parameters Sample outputFirmware Update Shows the firmware update parameters Sample output User’s Guide SH LOAdOther Commands SET DefaultExit SH FreeSET Poweron SH PoweronInit SaveNetware Commands UnprotectUser’s Guide SET Netw POlling SET Netw QServerSET Netw REscan SET Netw SErverEmail Printing Commands SET POP3 PAssword SET POP3 TImeoutSET Smtp ENable SET Smtp ADdressDLC / Netbeui Commands SET DLC ENableSET DLC TIMeout SH POP3Appletalk Commands SH DLCConfigures the Appletalk Zone for this server SET APPletalk ZOneWireless Security Configuration ExtendViewKey Selection SH NW SET NW KEY# SH NW Speed SET NW Certcn SH NW Certexp SH NW Inap SET NW Wpapsk