Sony SX-215 user manual Factory Default Settings, Pushbutton Functions

Page 12

User’s Guide

Pushbutton Functions

The front edge of the print server provides a momentary pushbutton that can be used to print a test/configuration page or reset the device to factory default settings.

Action	Function

Press pushbutton for > 1/8 second but < 5	Prints a test/configuration page on each connected port
seconds

Press pushbutton for > 5 seconds	Resets the device configuration to factory defaults. The
	unit will reinitialize itself after updating the
	configuration memory.

Factory Default Settings

The SX-200 Series Print Server is shipped with a default configuration. The settings can be changed to suit specific installation requirements via the ExtendView Utility, or other SNMP-based utilities, the embedded Web server, or via a Telnet connection to the Print Server’s internal console. The factory default settings can be easily restored at any time by performing a cold reset (press and hold the pushbutton on the device for more than five seconds).

Default Settings (wired and wireless print servers)

Parameter	Setting

IP Address	190.0.0.192

TCP/IP Method	AUTO (BootP and DHCP are enabled)

Password	access

Wireless Default Settings (wireless print servers only)

Parameter	Setting

Wireless Mode	Ad-Hoc (peer-to-peer)

RF Channel	11

SSID	printer (lower case)

Document #40181-420 Rev. B

12

Image 12

Contents SX-200/SX-215 User’s GuideUser’s Guide User’s Guide SET Port P1 Sojbusy SET IP TCP SH Smtp Introduction Package Contents Product OverviewUser’s Guide About This User’s Guide Windows System RequirementsOther Operating System Requirements User’s Guide Wireless Print Server Requirements User’s Guide Print Server Components LED Indicators Label Color State StatusFactory Default Settings Default Settings wired and wireless print serversWireless Default Settings wireless print servers only Pushbutton FunctionsHardware Installation Before You BeginUser’s Guide User’s Guide Verifying the Connection to the Printer Configuration and Management Configuration OptionsExtendView Utility Web Browser InterfaceHP Web JetAdmin Utility Configuration ConsoleDocument #40181-420 Rev. B User’s Guide Telnet User’s Guide Windows Print Queue Configuration Adding the Standard TCP/IP PortSelect the local printer, as shown below, and click Next User’s Guide User’s Guide Macintosh Print Queue Configuration Configuring to Print Using TCP/IP OS Troubleshooting Printing ProblemsIntroduction Troubleshooting Windows Problems Checking the Network Connection and CablingUser’s Guide Troubleshooting Network Configuration Problems User’s Guide Troubleshooting Wireless Configuration Problems Where to Get Help User’s Guide Returning Products Appendix a Safety and Regulatory Notices Information for United States Users SX-200User’s Guide Declaration of Conformity FCC SX-200 Information for Canadian Users IC notice SX-200User’s Guide Information for European Users SX-200 Declaration of Conformity CE SX-200User’s Guide Declaration of Conformity FCC SX-215 Information for Canadian Users IC Notice SX-215User’s Guide Appendix B Updating Firmware User’s Guide User’s Guide Loading New Firmware Macintosh OS-X User’s Guide Command console access information Telnet Command Console AccessSerial Port Command Console Access Network Commands SH NWSH NW Auth SET NW ENCSH NW Mode SH NW ENCSET NW KEY# SET NW KeyvalSH NW Speed CL NW BSsid SH NW Stats SET NW CertcnSH NW Certcn SET NW CERTCN2SH NW CERTCN2 SET NW CertexpSH NW Certexp SET NW CertkeySET NW PW SET NW InapSH NW Inap SET NW RealmSH NW Wpagroup SET NW WpapskSET NW Wpatrace SET NW IroamSH NW Iroam SET NW DFSSH NW DFS SET NW REGDOMainPort Commands SET NW WiredSH NW REGDOMain Sets Ethernet Speed to 10baseT, 100baseTX, or AutosenseUser’s Guide User’s Guide Parallel Port Commands Enable or disable bidirectional modeSET Port P1 BIDir Shows Port parameters Sample outputSET Port P1 Nbuf ENable DIsable Enable or disable PJL status initializationCL Port port JOB Server Information Commands USB Port CommandsSET SERVEr DEscription SET SERVEr NAmeSET Snmp SETCOMM1 SET Snmp SETCOMM2SH Serial User’s Guide SH SERVEr SH SERVEr COuntersSH Snmp SH VErsionService Commands SET Servi service name BOTSET Servi service name EOT SET Servi service name FIlterSET Servi service name FMS SET Servi service name FRSSET Servi service name IP SET Servi service name NAmeUser’s Guide SET Servi service name PRIority SH Servi PRI servicenumSET Servi service name RECeive SET Servi service name TCPString Commands TCP/IP CommandsUser’s Guide SET IP ACcess SH IP ACcessSET IP ARP ENable SET IP RANgeSET IP Chksum SET IP FTPSET IP Http SET IP LPD SET IP TCP SET IP TftpSH IP Shows TCP/IP related Parameters Sample outputFirmware Update Shows the firmware update parameters Sample output User’s Guide SH LOAdOther Commands SET DefaultExit SH FreeSET Poweron SH PoweronInit SaveNetware Commands UnprotectUser’s Guide SET Netw POlling SET Netw QServerSET Netw REscan SET Netw SErverEmail Printing Commands SET POP3 PAssword SET POP3 TImeoutSET Smtp ENable SET Smtp ADdressDLC / Netbeui Commands SET DLC ENableSET DLC TIMeout SH POP3Appletalk Commands SH DLCConfigures the Appletalk Zone for this server SET APPletalk ZOneWireless Security Configuration ExtendViewKey Selection SH NW SET NW KEY# SH NW Speed SET NW Certcn SH NW Certexp SH NW Inap SET NW Wpapsk