Nuance comm D60709-22 manual ∙ Device Properties, External Accounting Application Settings

Page 24

2 SafeCom Go Sharp - Device server

∙Device Properties:

oDsk: If the Device Security Kit is installed, Dsk must be set to True and then the addresses for Application UI and Web Service must be entered manually on the device web page under Application Settings, External Application Settings, and then

External Accounting Application Settings.

oNewModel: Set the property value to True if you are adding a

new Sharp model that has not yet been tested by SafeCom. The default value is False.

oReboot: Is set to True, which means that the device

automatically restarts. Set to False if you want to restart the device manually.

oSSL: Set to True to use SSL.

oserviceLogin: This service password must correspond to the

service password on the device. The default is service.

owelcomeScreen: Set the property value to True if you want the welcome screen (see below) displayed at the device before user

login. If the property value is False, then it is the login screen that is displayed for the user. The default value is 'true'.

owelcomeScreenTimeOut: Specify in seconds for when the welcome screen should timeout. The default value is '120'.

∙Device applications: Here it is specified if the users are allowed to Email, Copy, or Scan to USB without having to log in first. Check one or more of the three checkboxes to allow the users to perform these tasks without authentication.

The settings in the Device applications are tied to the welcome screen (see below). If none of the check boxes Email, Copy, or Scan to USB are selected, then the welcome screen only shows the option to Login and if enabled, Windows login. If one or more of three checkboxes Email, Copy, or Scan to USB are selected the users have the option to Login and to Copy/Scan from the welcome screen.

∙Enable logging: Select if log information should be collected.

∙Restore factory default sets all settings, except the password, to their default value (refer to 2.6.8).

∙Reconfigure device informs the device to reference the current SafeCom Device Server.

D60709-22

24

Image 24

Contents Nuance SafeCom Go Sharp Nuance Communications, Inc Table of Contents Regulatory information Index Introduction SafeCom Go SharpRequirements ∙ SafeCom Device ServerSafeCom Go Sharp supported Sharp OSA-enabled MFPs SafeCom ID Devices SafeCom Go Sharp supported SafeCom ID DevicesSerial Identification MethodSharp device passwords Available documentationAbout this manual Document history Introduction SafeCom Go Sharp Device server installation InstallationSafeCom Go Sharp Device server OverviewInbound on SafeCom Device Server Protocol Outbound on SafeCom Device Server ProtocolConfigure SafeCom Device Server Login to SafeCom Device ServerLogin to SafeCom Device Server Add SafeCom ServerDevice Server config.ini Description DefaultAdd device to a SafeCom Device Server Device iconsAdd device via SafeCom Device Server Click the Add device tool buttonAdd device via SafeCom Administrator Add device server Start SafeCom AdministratorAdd device server device SafeCom Go Sharp Device server Configure device in SafeCom Device Server Now Remote Operating. Please do not turn off the Power∙ Network settings ∙ Device information∙ Device settings Card ID code Card or ID codeExternal Accounting Application Settings ∙ Device PropertiesSelect login method Enable CopySafeCom Go Sharp How to Get the SafeCom Go Sharp softwareEnable E-mail Control user access rightsEnable SafeCom Mobile Pull Print Register deviceRestore factory default Configuration Field Default value SettingsUninstall SafeCom Go Sharp Installation with SafeCom Controller SafeCom ControllerWrite down the IP address of the device IP address / hostnameSwitch off the power to the device Connect hardwareAdd device in SafeCom Administrator IP address known from Dhcp serverFind it via Broadcasting Click Broadcast…Example mysharp.safecom.eu Configure the Sharp device web interface New Sharp devicesHttp//ip address/soapsharp/safecom.scx Click Standard Application Settings SafeCom Controller Application Name enter Pull Print Sharp Web Interface old models Click External Accounting3Click Standard Applications Application Name enter Pull Print Configure the SafeCom Controller Web Interface Login to the SafeCom Controller Web InterfaceAdvanced Configuration web SafeCom web Copy Idle Timeout is ignored Printer webPrinter Manufacturer should be Sharp SafeCom Go must be YES Enable copy tracking for Controller Change Copy Enabled to YES Click Save and ContinueSafeCom Go for Controller How to Specify SafeCom Server and device connectionSet password to prevent unauthorized access Disable the Test button Enable Copy ControlAssign a fixed IP address to the SafeCom Controller Select user identificationEnable High Speed Print Access Sharp MFP’s System SettingsResend configuration Click Restore Factory DefaultOpen the Sharp MFP’s web page and login Using SafeCom Go Sharp LoginSharp device with SafeCom Device Server Main menu Pull Print Document list Tap Pull PrintCopy Account Select billing codeRegister card with PUK code LogoutEnter PUK code Tap PUK code Enter PUK code and PIN code Tap PUK codeControl panel Login Login with ID code Tap ID codeLogin with ID code and PIN code Tap ID code Sharp device with SafeCom ControllerLogin with Windows Tap Documents Copy Troubleshooting SafeCom Administrator Unable to locate all SafeCom devicesSafeCom Help Desk Assistant ServletsMFP reports Could not access the accounting server… ERROR5000 Processing is in motionPrint performance is slow At the printer No billing codes availableDevice Server Configuration of devices failed SafeCom reader does not workRegulatory information Index Page Index D60709-22