Nuance comm D60709-22 manual Sharp Web Interface old models, Click External Accounting3

Page 38

3 SafeCom Controller

3.2.2Sharp Web Interface (old models)

Follow the steps below to configure the web interface on old Sharp devices. If you have a new Sharp device, refer to section 3.2.

The web interface MUST be configured to allow communication with the SafeCom Go Sharp solution.

1.Open the Sharp device’s web interface and login.

2.Scroll to and click Admin Mode. Enter the User name (default is admin) and Password (default is Sharp). On newer models the default password is admin (1.4). Click OK.

3.Scroll to and click External Applications.

4.Click External Accounting3.

3External Accounting link appears only if you have purchased the Sharp Sharp External Account Module (MX-AMX3). This module is a prerequisite for SafeCom Go Sharp.

D60709-22

38

Image 38

Contents Nuance SafeCom Go Sharp Nuance Communications, Inc Table of Contents Regulatory information Index Requirements IntroductionSafeCom Go Sharp ∙ SafeCom Device ServerSafeCom Go Sharp supported Sharp OSA-enabled MFPs Serial SafeCom ID DevicesSafeCom Go Sharp supported SafeCom ID Devices Identification MethodSharp device passwords Available documentationAbout this manual Document history Introduction SafeCom Go Sharp Device server SafeCom Go Sharp Device server installationInstallation OverviewInbound on SafeCom Device Server Protocol Outbound on SafeCom Device Server ProtocolLogin to SafeCom Device Server Configure SafeCom Device ServerLogin to SafeCom Device Server Add SafeCom ServerDevice Server config.ini Description DefaultAdd device to a SafeCom Device Server Device iconsAdd device via SafeCom Device Server Click the Add device tool buttonAdd device via SafeCom Administrator Add device server Start SafeCom AdministratorAdd device server device SafeCom Go Sharp Device server Configure device in SafeCom Device Server Now Remote Operating. Please do not turn off the Power∙ Network settings ∙ Device information∙ Device settings Card ID code Card or ID codeExternal Accounting Application Settings ∙ Device PropertiesSafeCom Go Sharp How to Select login methodEnable Copy Get the SafeCom Go Sharp softwareEnable SafeCom Mobile Pull Print Enable E-mailControl user access rights Register deviceRestore factory default Configuration Field Default value SettingsUninstall SafeCom Go Sharp Write down the IP address of the device Installation with SafeCom ControllerSafeCom Controller IP address / hostnameSwitch off the power to the device Connect hardwareFind it via Broadcasting Add device in SafeCom AdministratorIP address known from Dhcp server Click Broadcast…Example mysharp.safecom.eu Configure the Sharp device web interface New Sharp devicesHttp//ip address/soapsharp/safecom.scx Click Standard Application Settings SafeCom Controller Application Name enter Pull Print Sharp Web Interface old models Click External Accounting3Click Standard Applications Application Name enter Pull Print Advanced Configuration web Configure the SafeCom Controller Web InterfaceLogin to the SafeCom Controller Web Interface SafeCom web Printer Manufacturer should be Sharp SafeCom Go must be YES Copy Idle Timeout is ignoredPrinter web SafeCom Go for Controller How to Enable copy tracking for ControllerChange Copy Enabled to YES Click Save and Continue Specify SafeCom Server and device connectionSet password to prevent unauthorized access Assign a fixed IP address to the SafeCom Controller Disable the Test buttonEnable Copy Control Select user identificationResend configuration Enable High Speed PrintAccess Sharp MFP’s System Settings Click Restore Factory DefaultOpen the Sharp MFP’s web page and login Sharp device with SafeCom Device Server Using SafeCom Go SharpLogin Main menu Pull Print Document list Tap Pull PrintCopy Account Select billing codeEnter PUK code Tap PUK code Register card with PUK codeLogout Enter PUK code and PIN code Tap PUK codeLogin with ID code and PIN code Tap ID code Control panel LoginLogin with ID code Tap ID code Sharp device with SafeCom ControllerLogin with Windows Tap Documents Copy SafeCom Help Desk Assistant TroubleshootingSafeCom Administrator Unable to locate all SafeCom devices ServletsPrint performance is slow MFP reports Could not access the accounting server…ERROR5000 Processing is in motion At the printer No billing codes availableDevice Server Configuration of devices failed SafeCom reader does not workRegulatory information Index Page Index D60709-22